flexfax: Problems with GVC Modems

[Philipp Steinkr�ger <steinkrueger@oberberg-online.de>]

Dear Readers,


i have a problem with recieving faxes with my GVC 14.4 Modem.
I am using Hylafax 4.0pl2 on a Debian-Linux Box.

Faxgetty detects the modem as : Modem Rockwell R32ACL/E.C.      Version
T.
This is what a ati4 shows: F-1114V/R6 (GM) V.6.16.12
                           Modemchip: Rockwell RC144DPI
                           Fax Class 1 and Class 2

I expirienced "Unspecified Phase D Error (Code 100)" "Ring detected
without successfull handshake"
and "T.30 Timeout".
I checked the Hylafaq and the mailinglist-archive and tried to reduce
the Modemrate to 19200.
I changed the Modemclass to 1, but the Modem is still unable to recieve
faxes from severeal
faxmachines.
I also tried to set Use2d: No and Modemflowcontrol: XONXOFF, without
success.

Here is a log of an unsuccessfull Fax Connection:

May 20 08:36:48.41: [  549]: SESSION BEGIN 00000509 492261814919
May 20 08:36:48.41: [  549]: <-- [4:ATA\r]
May 20 08:36:56.62: [  549]: --> [5:+FCON]
May 20 08:36:56.62: [  549]: MODEM set baud rate: 19200 baud (flow
control unchanged)
May 20 08:36:56.62: [  549]: MODEM set baud rate: 19200 baud, input flow
XON/XOFF, output flow XON/XOFF
May 20 08:36:56.62: [  549]: ANSWER: FAX CONNECTION
May 20 08:36:56.62: [  549]: STATE CHANGE: ANSWERING -> RECEIVING
May 20 08:36:56.62: [  549]: MODEM input buffering enabled
May 20 08:36:56.62: [  549]: RECV FAX: begin
May 20 08:36:58.60: [  549]: --> [29:+FTSI: "          2261 87541"]
May 20 08:36:58.60: [  549]: REMOTE TSI "2261 87541"
May 20 08:36:58.60: [  549]: --> [22:+FDCS: 0,3,0,2,0,0,0,3]
May 20 08:36:58.60: [  549]: REMOTE wants 9600 bit/s
May 20 08:36:58.60: [  549]: REMOTE wants page width 1728 pixels in 215
mm
May 20 08:36:58.60: [  549]: REMOTE wants unlimited page length 
May 20 08:36:58.60: [  549]: REMOTE wants 3.85 line/mm
May 20 08:36:58.60: [  549]: REMOTE wants 1-D MR
May 20 08:37:00.55: [  549]: --> [2:OK]
May 20 08:37:00.55: [  549]: <-- [7:AT+FDR\r]
May 20 08:37:02.30: [  549]: --> [5:+FCFR]
May 20 08:37:02.30: [  549]: --> [22:+FDCS: 0,3,0,2,0,0,0,3]
May 20 08:37:02.30: [  549]: REMOTE wants 9600 bit/s
May 20 08:37:02.30: [  549]: REMOTE wants page width 1728 pixels in 215
mm
May 20 08:37:02.30: [  549]: REMOTE wants unlimited page length 
May 20 08:37:02.30: [  549]: REMOTE wants 3.85 line/mm
May 20 08:37:02.30: [  549]: REMOTE wants 1-D MR
May 20 08:37:03.13: [  549]: --> [7:CONNECT]
May 20 08:37:03.13: [  549]: RECV: begin page
May 20 08:37:03.13: [  549]: MODEM set XON/XOFF/FLUSH: input ignored,
output generated
May 20 08:37:03.13: [  549]: RECV: send trigger 022
May 20 08:37:03.13: [  549]: <-- data [1]
May 20 08:37:30.65: [  549]: RECV/CQ: Bad 1D pixel count, row 1104, got
0, expected 1728
May 20 08:37:30.65: [  549]: RECV/CQ: Bad 1D pixel count, row 1105, got
0, expected 1728
May 20 08:37:30.65: [  549]: RECV/CQ: Bad 1D pixel count, row 1106, got
0, expected 1728
May 20 08:37:30.65: [  549]: RECV/CQ: Bad 1D pixel count, row 1107, got
0, expected 1728
May 20 08:37:30.65: [  549]: RECV/CQ: Adjusting for trailing noise (4
run)
May 20 08:37:30.65: [  549]: RECV: 1104 total lines, 0 bad lines, 0
consecutive bad lines
May 20 08:37:30.65: [  549]: MODEM set XON/XOFF/DRAIN: input
interpreted, output disabled
May 20 08:37:30.65: [  549]: --> [8:+FPTS: 1]
May 20 08:37:31.89: [  549]: --> [7:+FET: 0]
May 20 08:37:31.89: [  549]: RECV recv MPS (more pages, same document)
May 20 08:37:31.89: [  549]: --> [2:OK]
May 20 08:37:31.90: [  549]: RECV send MCF (message confirmation)
May 20 08:37:31.90: [  549]: RECV FAX (00000509): from 2261 87541, page
1 in 0:31, INF, 3.85 line/mm, 1-D MR
May 20 08:37:31.90: [  549]: <-- [7:AT+FDR\r]
May 20 08:37:34.38: [  549]: --> [7:CONNECT]
May 20 08:37:34.38: [  549]: RECV: begin page
May 20 08:37:34.38: [  549]: MODEM set XON/XOFF/FLUSH: input ignored,
output generated
May 20 08:37:34.38: [  549]: RECV: send trigger 022
May 20 08:37:34.38: [  549]: <-- data [1]
May 20 08:37:34.97: [  549]: RECV/CQ: Bad 1D pixel count, row 0, got
2433, expected 1728
May 20 08:37:35.82: [  549]: RECV/CQ: Adjusting for trailing noise (1
run)
May 20 08:37:35.82: [  549]: RECV: 0 total lines, 0 bad lines, 0
consecutive bad lines
May 20 08:37:35.82: [  549]: MODEM set XON/XOFF/DRAIN: input
interpreted, output disabled
May 20 08:37:35.82: [  549]: --> [8:+FPTS: 1]
May 20 08:37:57.66: [  549]: --> [10:+FHNG: 100]
May 20 08:37:57.66: [  549]: REMOTE HANGUP: Unspecified Phase D error
(code 100)
May 20 08:37:57.66: [  549]: --> [2:OK]
May 20 08:37:57.66: [  549]: RECV FAX (00000509): recvq/fax00052.tif
from 2261 87541, route to <unspecified>, 1 pages in 1:01
May 20 08:37:57.66: [  549]: RECV FAX: Unspecified Phase D error
May 20 08:37:57.66: [  549]: RECV FAX (00000509): session with 2261
87541 terminated abnormally: Unspecified Phase D error
May 20 08:37:57.66: [  549]: RECV FAX: bin/faxrcvd "recvq/fax00052.tif"
"ttyS1" "00000509" "Unspecified Phase D error"
May 20 08:37:57.91: [  549]: RECV FAX: end
May 20 08:37:57.91: [  549]: SESSION END


I have similar problems with a Elsa 33.6TQV. I have to collect some log
files and do some tests, but i guess i will have
to ask the list with this problem, too.


If you need more information or whatelse, please tell me.


Regards,

Philipp