 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
Hylafax receive errors
- To: flexfax@sgi.com
- Subject: flexfax: Hylafax receive errors
- From: Simone Fortina <simone.f@hotpop.com>
- Date: Sun, 02 May 1999 22:45:23 +0200
I'm having lots of trouble setting up an old Etech P1414MX for fax receive using Hylafax 4.0pl2 under linux 2.2.7. I get garbage faxes all of the times. I have tried xon/xoff-rts/cts and no flow control, 19200 and 9600 bps, DC1 and DC2 but... Please help!! I enclose config.modem, session log and server log. My config.modem file: # # Generic Class 2 modem configuration. # # EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP # CountryCode: 39 AreaCode: 039 FAXNumber: +39.039.6880122 LongDistancePrefix: 0 InternationalPrefix: 00 DialStringRules: etc/dialrules ServerTracing: 0x85fd SessionTracing: 0x85fd RecvFileMode: 0644 LogFileMode: 0600 DeviceMode: 0600 RingsBeforeAnswer: 1 SpeakerVolume: quiet GettyArgs: "-h %l %s" LocalIdentifier: "Thule sas-Vimercate" TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%p of %%t" MaxRecvPages: 25 PercentGoodLines: 0 # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class2 # use this to supply a hint ModemRate: 19200 # max rate for DCE-DTE communication ModemFlowControl: rtscts # hardware flow control assumed ModemHardFlowCmd: AT$F4 # Hardware flow control ModemSoftFlowCmd: AT$F0 # Software flow control ModemNoFlowCmd: AT$F5 ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not) # ModemDialCmd: ATDT%s@ # T for tone dialing, @ for silence ModemSetVolumeCmd: "ATM0 ATM1 ATM1 ATM1 ATM1" # # Configuration parameters for Class 2 modems. # Class2DDISCmd: AT+FDIS # disable pre-dial DIS command hack Class2TBCCmd: "" My session log: May 02 20:27:05.75: [ 2345]: SESSION BEGIN 00000030 390396880122 May 02 20:27:05.76: [ 2345]: <-- [4:ATA\r] May 02 20:27:09.01: [ 2345]: --> [3:FAX] May 02 20:27:09.01: [ 2345]: ANSWER: FAX CONNECTION May 02 20:27:09.01: [ 2345]: STATE CHANGE: ANSWERING -> RECEIVING May 02 20:27:09.01: [ 2345]: MODEM input buffering enabled May 02 20:27:13.45: [ 2345]: --> [5:+FCON] May 02 20:27:16.80: [ 2345]: --> [29:+FTSI: " Thule sas-Monza"] May 02 20:27:16.80: [ 2345]: --> [22:+FDCS: 1,5,0,2,0,0,0,0] May 02 20:27:16.80: [ 2345]: --> [2:OK] May 02 20:27:16.80: [ 2345]: <-- [7:AT+FDR\r] May 02 20:27:17.04: [ 2345]: --> [5:+FCFR] May 02 20:27:18.94: [ 2345]: --> [7:CONNECT] May 02 20:27:18.94: [ 2345]: <-- data [1] May 02 20:27:19.15: [ 2345]: RECV/CQ: Bad 1D pixel count, row 0, got 1784, expected 1728 May 02 20:27:19.64: [ 2345]: RECV/CQ: Invalid BlackTable code word, row 1, x 142 May 02 20:27:19.64: [ 2345]: RECV/CQ: Bad 1D pixel count, row 1, got 142, expected 1728 May 02 20:27:19.64: [ 2345]: RECV/CQ: Bad 1D pixel count, row 2, got 1746, expected 1728 May 02 20:27:20.13: [ 2345]: RECV/CQ: Bad 1D pixel count, row 3, got 1928, expected 1728 May 02 20:27:20.20: [ 2345]: RECV/CQ: Invalid WhiteTable code word, row 4, x 0 May 02 20:27:20.20: [ 2345]: RECV/CQ: Bad 1D pixel count, row 4, got 0, expected 1728 May 02 20:27:20.20: [ 2345]: RECV/CQ: Invalid WhiteTable code word, row 5, x 0 May 02 20:27:20.20: [ 2345]: RECV/CQ: Bad 1D pixel count, row 5, got 0, expected 1728 May 02 20:27:20.27: [ 2345]: RECV/CQ: Invalid BlackTable code word, row 6, x 411 May 02 20:27:20.27: [ 2345]: RECV/CQ: Bad 1D pixel count, row 6, got 411, expected 1728 May 02 20:27:20.27: [ 2345]: RECV/CQ: Invalid WhiteTable code word, row 7, x 0 May 02 20:27:20.27: [ 2345]: RECV/CQ: Bad 1D pixel count, row 7, got 0, expected 1728 May 02 20:27:20.27: [ 2345]: RECV/CQ: Invalid WhiteTable code word, row 8, x 79 May 02 20:27:20.27: [ 2345]: RECV/CQ: Bad 1D pixel count, row 8, got 79, expected 1728 May 02 20:27:20.34: [ 2345]: RECV/CQ: Invalid BlackTable code word, row 9, x 1923 May 02 20:27:20.34: [ 2345]: RECV/CQ: Bad 1D pixel count, row 9, got 1923, expected 1728 May 02 20:27:20.41: [ 2345]: RECV/CQ: Invalid WhiteTable code word, row 10, x 1007 May 02 20:27:20.41: [ 2345]: RECV/CQ: Bad 1D pixel count, row 10, got 1007, expected 1728 May 02 20:27:20.48: [ 2345]: RECV/CQ: Bad 1D pixel count, row 11, got 1964, expected 1728 May 02 20:27:20.48: [ 2345]: RECV/CQ: Bad 1D pixel count, row 12, got 3536, expected 1728 May 02 20:27:20.76: [ 2345]: RECV/CQ: Invalid WhiteTable code word, row 13, x 320 May 02 20:27:20.76: [ 2345]: RECV/CQ: Bad 1D pixel count, row 13, got 320, expected 1728 May 02 20:27:20.83: [ 2345]: RECV/CQ: Bad 1D pixel count, row 14, got 2079, expected 1728 May 02 20:27:21.19: [ 2345]: RECV/CQ: Bad 1D pixel count, row 15, got 2677, expected 1728 May 02 20:27:21.26: [ 2345]: RECV/CQ: Invalid WhiteTable code word, row 16, x 31 May 02 20:27:21.26: [ 2345]: RECV/CQ: Bad 1D pixel count, row 16, got 31, expected 1728 May 02 20:27:21.26: [ 2345]: RECV/CQ: Invalid BlackTable code word, row 17, x 244 May 02 20:27:21.26: [ 2345]: RECV/CQ: Bad 1D pixel count, row 17, got 244, expected 1728 May 02 20:27:21.33: [ 2345]: RECV/CQ: Bad 1D pixel count, row 18, got 2117, expected 1728 May 02 20:27:21.33: [ 2345]: RECV/CQ: Invalid WhiteTable code word, row 19, x 643 May 02 20:27:21.33: [ 2345]: RECV/CQ: Bad 1D pixel count, row 19, got 643, expected 1728 May 02 20:27:21.47: [ 2345]: RECV/CQ: Bad 1D pixel count, row 20, got 1067, expected 1728 May 02 20:27:21.47: [ 2345]: RECV/CQ: Invalid BlackTable code word, row 21, x 607 May 02 20:27:21.47: [ 2345]: RECV/CQ: Bad 1D pixel count, row 21, got 607, expected 1728 May 02 20:27:21.47: [ 2345]: RECV/CQ: Invalid BlackTable code word, row 22, x 795 May 02 20:27:21.47: [ 2345]: RECV/CQ: Bad 1D pixel count, row 22, got 795, expected 1728 May 02 20:27:21.47: [ 2345]: RECV/CQ: Invalid WhiteTable code word, row 23, x 0 May 02 20:27:21.47: [ 2345]: RECV/CQ: Bad 1D pixel count, row 23, got 0, expected 1728 May 02 20:27:21.47: [ 2345]: RECV/CQ: Invalid BlackTable code word, row 24, x 1246 May 02 20:27:21.47: [ 2345]: RECV/CQ: Bad 1D pixel count, row 24, got 1246, expected 1728 May 02 20:27:26.03: [ 2345]: RECV/CQ: Bad 1D pixel count, row 25, got 20, expected 1728 May 02 20:27:27.41: [ 2345]: --> [17:+FPTS: 1,2219,0,0] May 02 20:27:27.41: [ 2345]: --> [7:+FET: 2] May 02 20:27:27.41: [ 2345]: --> [2:OK] May 02 20:27:27.41: [ 2345]: RECV FAX (00000030): from Thule sas-Monza, page 1 in 0:11, INF, 7.7 line/mm, 1-D MR May 02 20:27:27.42: [ 2345]: RECV FAX (00000030): recvq/fax00020.tif from Thule sas-Monza, route to <unspecified>, 1 pages in 0:18 May 02 20:27:27.42: [ 2345]: <-- [7:AT+FDR\r] May 02 20:27:30.44: [ 2345]: --> [8:+FHNG: 0] May 02 20:27:30.44: [ 2345]: RECV FAX: bin/faxrcvd "recvq/fax00020.tif" "modem" "00000030" "" May 02 20:27:30.83: [ 2345]: SESSION END My server log: May 2 20:27:05 turbujuk FaxGetty[2345]: STATE CHANGE: RUNNING -> LISTENING May 2 20:27:05 turbujuk FaxGetty[2345]: MODEM input buffering enabled May 2 20:27:05 turbujuk FaxGetty[2345]: --> [4:RING] May 2 20:27:05 turbujuk FaxGetty[2345]: STATE CHANGE: LISTENING -> ANSWERING May 2 20:27:05 turbujuk FaxGetty[2345]: MODEM input buffering enabled May 2 20:27:09 turbujuk FaxGetty[2345]: ANSWER: FAX CONNECTION May 2 20:27:27 turbujuk FaxGetty[2345]: RECV FAX (00000030): from Thule sas-Monza, page 1 in 0:11, INF, 7.7 line/mm, 1-D MR May 2 20:27:27 turbujuk FaxGetty[2345]: RECV FAX (00000030): recvq/fax00020.tif from Thule sas-Monza, route to <unspecified>, 1 pages in 0:18 May 2 20:27:30 turbujuk FaxGetty[2345]: RECV FAX: bin/faxrcvd "recvq/fax00020.tif" "modem" "00000030" "" May 2 20:27:30 turbujuk FaxGetty[2345]: <-- [5:ATH0\r] May 2 20:27:30 turbujuk FaxGetty[2345]: --> [2:OK] May 2 20:27:30 turbujuk FaxGetty[2345]: MODEM set DTR OFF May 2 20:27:30 turbujuk FaxGetty[2345]: MODEM set DTR OFF May 2 20:27:33 turbujuk FaxGetty[2345]: MODEM set DTR ON May 2 20:27:33 turbujuk FaxGetty[2345]: MODEM set baud rate: 19200 baud, input flow RTS/CTS, output flow RTS/CTS May 2 20:27:33 turbujuk FaxGetty[2345]: MODEM flush i/o May 2 20:27:33 turbujuk FaxGetty[2345]: <-- [15:ATE0V1Q0S0=0H0\r] May 2 20:27:33 turbujuk FaxGetty[2345]: --> [2:OK] May 2 20:27:33 turbujuk FaxGetty[2345]: <-- [21:ATS8=2S7=60$F4&D2&C1\r] May 2 20:27:33 turbujuk FaxGetty[2345]: --> [2:OK] May 2 20:27:33 turbujuk FaxGetty[2345]: <-- [12:AT+FCLASS=?\r] May 2 20:27:34 turbujuk FaxGetty[2345]: --> [3:0,2] May 2 20:27:34 turbujuk FaxGetty[2345]: --> [2:OK] May 2 20:27:34 turbujuk FaxGetty[2345]: MODEM Supports "Data" May 2 20:27:34 turbujuk FaxGetty[2345]: MODEM Supports "Class 2" May 2 20:27:34 turbujuk FaxGetty[2345]: <-- [12:AT+FCLASS=2\r] May 2 20:27:34 turbujuk FaxGetty[2345]: --> [2:OK] May 2 20:27:34 turbujuk FaxGetty[2345]: <-- [9:AT+FMFR?\r] May 2 20:27:34 turbujuk FaxGetty[2345]: --> [12:E-Tech, Inc.] May 2 20:27:34 turbujuk FaxGetty[2345]: --> [2:OK] May 2 20:27:34 turbujuk FaxGetty[2345]: MODEM: Mfr E-Tech, Inc. May 2 20:27:34 turbujuk FaxGetty[2345]: <-- [9:AT+FMDL?\r] May 2 20:27:34 turbujuk FaxGetty[2345]: --> [5:ERROR] May 2 20:27:34 turbujuk FaxGetty[2345]: <-- [9:AT+FREV?\r] May 2 20:27:35 turbujuk FaxGetty[2345]: --> [5:ERROR] May 2 20:27:35 turbujuk FaxGetty[2345]: <-- [10:AT+FDCC=?\r] May 2 20:27:35 turbujuk FaxGetty[2345]: --> [35:(0,1),(0-5),(0-4),(0-2),0,0,0,(0-7)] May 2 20:27:35 turbujuk FaxGetty[2345]: --> [2:OK] May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 3.85 line/mm May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 7.7 line/mm May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 2400 bit/s May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 4800 bit/s May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 7200 bit/s May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 9600 bit/s May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 12000 bit/s May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 14400 bit/s May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports page width 1728 pixels in 215 mm May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports page width 2048 pixels in 255 mm May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports page width 2432 pixels in 303 mm May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports page width 1216 pixels in 151 mm May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports page width 864 pixels in 107 mm May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports A4 page length (297 mm) May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports B4 page length (364 mm) May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports unlimited page length May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 1-D MR May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 0 ms/scanline May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 5 ms/scanline May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 10 ms, 5 ms/scanline May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 10 ms/scanline May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 20 ms, 10 ms/scanline May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 20 ms/scanline May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 40 ms, 20 ms/scanline May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports 40 ms/scanline May 2 20:27:35 turbujuk FaxGetty[2345]: <-- [9:AT+FCQ=?\r] May 2 20:27:35 turbujuk FaxGetty[2345]: --> [5:ERROR] May 2 20:27:35 turbujuk FaxGetty[2345]: MODEM Supports no copy quality checking May 2 20:27:35 turbujuk FaxGetty[2345]: <-- [9:AT+FAP=?\r] May 2 20:27:35 turbujuk FaxGetty[2345]: --> [5:ERROR] May 2 20:27:35 turbujuk FaxGetty[2345]: <-- [10:AT+FSPL=?\r] May 2 20:27:36 turbujuk FaxGetty[2345]: --> [2:OK] May 2 20:27:36 turbujuk FaxGetty[2345]: <-- [12:AT+FCLASS=2\r] May 2 20:27:36 turbujuk FaxGetty[2345]: --> [2:OK] May 2 20:27:36 turbujuk FaxGetty[2345]: <-- [10:AT+FTBC=0\r] May 2 20:27:36 turbujuk FaxGetty[2345]: --> [5:ERROR] May 2 20:27:36 turbujuk FaxGetty[2345]: MODEM Command error May 2 20:27:36 turbujuk FaxGetty[2345]: <-- [10:AT+FBOR=0\r] May 2 20:27:36 turbujuk FaxGetty[2345]: --> [2:OK] May 2 20:27:36 turbujuk FaxGetty[2345]: <-- [13:AT+FPHCTO=30\r] May 2 20:27:37 turbujuk FaxGetty[2345]: --> [2:OK] May 2 20:27:37 turbujuk FaxGetty[2345]: <-- [10:AT+FBUG=1\r] May 2 20:27:37 turbujuk FaxGetty[2345]: --> [5:ERROR] May 2 20:27:37 turbujuk FaxGetty[2345]: MODEM Command error May 2 20:27:37 turbujuk FaxGetty[2345]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r] May 2 20:27:37 turbujuk FaxGetty[2345]: --> [2:OK] May 2 20:27:37 turbujuk FaxGetty[2345]: MODEM E-TECH, INC. / May 2 20:27:37 turbujuk FaxGetty[2345]: <-- [5:ATM1\r] May 2 20:27:37 turbujuk FaxGetty[2345]: --> [2:OK] May 2 20:27:37 turbujuk FaxGetty[2345]: <-- [9:AT+FCR=1\r] May 2 20:27:38 turbujuk FaxGetty[2345]: --> [2:OK] May 2 20:27:38 turbujuk FaxGetty[2345]: <-- [30:AT+FLID="Thule sas-Vimercate"\r] May 2 20:27:38 turbujuk FaxGetty[2345]: --> [2:OK] May 2 20:27:38 turbujuk FaxGetty[2345]: STATE CHANGE: RECEIVING -> RUNNING May 2 20:27:38 turbujuk FaxGetty[2345]: MODEM input buffering disabled
- Follow-Ups:
- Re: Hylafax receive errors
- From: David Woolley <david@djwhome.demon.co.uk>
- Re: Hylafax receive errors
- Prev by Date: Compile problem on Alpha Linux
- Next by Date: Re: Compile problem on Alpha Linux
- Prev by thread: Re: Compile problem on Alpha Linux
- Next by thread: Re: Hylafax receive errors
- Index(es):
Project hosted by iFAX Solutions