Re: flexfax: too much delay between TCF and +FDR?

[Darrell Berry <darrellb@hhcl.com>]

David Woolley wrote:
> 
> >
> > any idea what this means? can't find it in the FAQ, and we are seeing
> > this a LOT! (USR Sportster)
> 
> No.  Because you have deleted the output from Hylafax that caused
> the modem to generate an "ERROR" response.  Some additional context
> before this may also be needed.

oops:

whole log is attached...any help gratefully received!

--

An attempt to receive facsimile on modem failed because:

    Unspecified Phase C error, including too much delay between TCF and
+FDR command

    ---- Transcript of session follows ----

Feb 19 16:34:09.49: [  333]: SESSION BEGIN 00000727 441714362677
Feb 19 16:34:09.49: [  333]: <-- [4:ATA\r]
Feb 19 16:34:17.05: [  333]: --> [4:+FCO]
Feb 19 16:34:17.05: [  333]: ANSWER: FAX CONNECTION
Feb 19 16:34:17.05: [  333]: RECV FAX: begin
Feb 19 16:34:18.94: [  333]: --> [27:+FTI:"         01715665100"]
Feb 19 16:34:18.94: [  333]: REMOTE TSI "01715665100"
Feb 19 16:34:18.94: [  333]: --> [20:+FCS:0,5,0,2,0,0,0,1]
Feb 19 16:34:18.94: [  333]: REMOTE wants 14400 bit/s
Feb 19 16:34:18.94: [  333]: REMOTE wants page width 1728 pixels in 215
mm
Feb 19 16:34:18.94: [  333]: REMOTE wants unlimited page length 
Feb 19 16:34:18.94: [  333]: REMOTE wants 3.85 line/mm
Feb 19 16:34:18.94: [  333]: REMOTE wants 1-D MR
Feb 19 16:34:18.94: [  333]: --> [2:OK]
Feb 19 16:34:18.94: [  333]: <-- [7:AT+FDR\r]
Feb 19 16:34:24.39: [  333]: --> [7:CONNECT]
Feb 19 16:34:24.39: [  333]: RECV: begin page
Feb 19 16:34:24.39: [  333]: RECV: send trigger 022
Feb 19 16:34:25.34: [  333]: RECV: 0 total lines, 0 bad lines, 0
consecutive bad lines
Feb 19 16:34:25.45: [  333]: --> [14:+FPS:1,4,0,0,0]
Feb 19 16:34:30.45: [  333]: --> [5:ERROR]
Feb 19 16:34:30.45: [  333]: MODEM Command error
Feb 19 16:34:30.45: [  333]: REMOTE HANGUP: Unspecified Phase C error,
including too much delay between TCF and +FDR command (code 90)
Feb 19 16:34:30.45: [  333]: RECV FAX (00000727): recvq/fax00230.tif
from 01715665100, route to <unspecified>, 0 pages in 0:13
Feb 19 16:34:30.45: [  333]: RECV FAX: Unspecified Phase C error,
including too much delay between TCF and +FDR command
Feb 19 16:34:30.45: [  333]: <-- [7:AT+FKS\r]
Feb 19 16:34:30.56: [  333]: --> [5:ERROR]
Feb 19 16:34:30.56: [  333]: MODEM Command error
Feb 19 16:34:30.56: [  333]: RECV FAX (00000727): session with
01715665100 terminated abnormally: Unspecified Phase C error, including
too much delay between TCF and +FDR command
Feb 19 16:34:30.56: [  333]: RECV FAX: bin/faxrcvd "recvq/fax00230.tif"
"modem" "00000727" "Unspecified Phase C error, including too much delay
between TCF and +FDR command"