Re: flexfax: Problem viewing(recieving?)

[Finn Guttormsen <finng@ifi.uio.no>]

David Woolley wrote:

> >
> > I cant recieve or view the whole fax after its finished recieving.
>
> The session log would almost certainly have been more use than the
> image (if this had been a newsgroup, the image may well have generated
> an automatic cancel).
>
> > Only the top of a page is shown. See attachment.
>
> I don't have any TIFF viewing tools on the home machine, but it is
> quite clear that this file is much too short, so you need to look
> at the session log to find out why - e.g. was there an overrun because
> of bad flow control, or did the sender abort the transmission, or the
> modem abort reception.

Hi, and thank you for the replies on my questions!

I'm sending the sessionlog for a recieved fax. I cant see any obvious
errors, but I'm not to experienced with this ...
Tha fax is an bw A4 page sent from a Toshiba faxmachine
----------------------------------------------------

Feb 21 10:25:28.49: [  449]: SESSION BEGIN 00000019 4722655368
Feb 21 10:25:28.50: [  449]: <-- [4:ATA\r]
Feb 21 10:25:29.88: [  449]: --> [3:FAX]
Feb 21 10:25:29.88: [  449]: ANSWER: FAX CONNECTION
Feb 21 10:25:29.88: [  449]: RECV FAX: begin
Feb 21 10:25:37.40: [  449]: --> [5:    $�M�]
Feb 21 10:25:37.40: [  449]: --> [29:+FTSI: "         47 22655368"]
Feb 21 10:25:37.40: [  449]: REMOTE TSI "47 22655368"
Feb 21 10:25:37.73: [  449]: --> [22:+FDCS: 1,3,0,2,0,0,0,3]
Feb 21 10:25:37.73: [  449]: REMOTE wants 9600 bit/s
Feb 21 10:25:37.73: [  449]: REMOTE wants page width 1728 pixels in 215
mm
Feb 21 10:25:37.73: [  449]: REMOTE wants unlimited page length
Feb 21 10:25:37.73: [  449]: REMOTE wants 7.7 line/mm
Feb 21 10:25:37.73: [  449]: REMOTE wants 1-D MR
Feb 21 10:25:37.84: [  449]: --> [2:OK]
Feb 21 10:25:37.84: [  449]: <-- [7:AT+FDR\r]
Feb 21 10:25:39.44: [  449]: --> [5:+FCFR]
Feb 21 10:25:41.83: [  449]: --> [22:+FDCS: 1,3,0,2,0,0,0,3]
Feb 21 10:25:41.83: [  449]: REMOTE wants 9600 bit/s
Feb 21 10:25:41.83: [  449]: REMOTE wants page width 1728 pixels in 215
mm
Feb 21 10:25:41.83: [  449]: REMOTE wants unlimited page length
Feb 21 10:25:41.83: [  449]: REMOTE wants 7.7 line/mm
Feb 21 10:25:41.83: [  449]: REMOTE wants 1-D MR
Feb 21 10:25:41.83: [  449]: --> [7:CONNECT]
Feb 21 10:25:41.83: [  449]: RECV: begin page
Feb 21 10:25:41.83: [  449]: RECV: send trigger 021
Feb 21 10:25:41.83: [  449]: <-- data [1]
Feb 21 10:26:24.49: [  449]: RECV: 17 total lines, 0 bad lines, 0
consecutive bad lines
Feb 21 10:26:24.50: [  449]: --> [17:+FPTS: 1,2219,0,0]
Feb 21 10:26:25.11: [  449]: --> [7:+FET: 2]
Feb 21 10:26:25.11: [  449]: RECV recv EOP (no more pages or documents)
Feb 21 10:26:25.22: [  449]: --> [2:OK]
Feb 21 10:26:25.22: [  449]: RECV send MCF (message confirmation)
Feb 21 10:26:25.22: [  449]: RECV FAX (00000019): from 47 22655368, page
1 in 0:48, INF, 7.7 line/mm, 1-D MR
Feb 21 10:26:25.22: [  449]: RECV FAX (00000019): recvq/fax00011.tif from
47 22655368, route to <unspecified>, 1 pages in 0:56
Feb 21 10:26:25.23: [  449]: <-- [7:AT+FDR\r]
Feb 21 10:26:28.33: [  449]: --> [8:+FHNG: 0]
Feb 21 10:26:28.33: [  449]: REMOTE HANGUP: Normal and proper end of
connection (code 0)
Feb 21 10:26:28.33: [  449]: RECV FAX: bin/faxrcvd "recvq/fax00011.tif"
"cua1" "00000019" ""
Feb 21 10:26:29.20: [  449]: RECV FAX: end
Feb 21 10:26:29.20: [  449]: SESSION END

------------------------------------------------

Another thing:

In another mail you recomended I rm the /dev/modem and point faxgetty to
the real device (/dev/cua1 in this case)
I've done this. Everything is as it where, and I still dont get hfaxd
when I run ps ax | grep fax - which was one of my questions.
It seems as if this daemon isn't running..? Is that not a problem?

(I have RH 5.2 on a single maschine with some user-account.
no ./hylarc files either...)

I realy appreciate you bothering to reply to my previous mails, and I
hope you can help me with this as well.

Respectfully,
Finn Guttormsen


PS: My modem is a UCOM Skylink v.34 (33600bps) with a Rockwell chipset.