flexfax: No response to MPS or EOP

[Norbert Lesch <norbert.lesch@post.rwth-aachen.de>]

Hello HylaFax experts,
I am using Hylafax 4.0pl2-13 on SusE Linux 5.3 .
The modem is a Motorola 3400 (It identifies as motorola lifestyle 28.8)
class 1 faxmodem.
I tried the configuration files gvc-288 and moto-288.
All is fine except that sending a fax to a  special faximile
(Hewlett Packard OfficeJet LX  ) results in the following
error messages:


Error: No response to MPS or EOP repeated 3 tries


    ---- Transcript of session follows ----

Jan 20 01:09:40.26: [ 3611]: SESSION BEGIN 00000017 492418888313
Jan 20 01:09:40.26: [ 3611]: SEND FAX: JOB 10 DEST +49 241 8888313
COMMID
00000017
Jan 20 01:09:40.26: [ 3611]: MODEM set DTR OFF
Jan 20 01:09:40.26: [ 3611]: DELAY 2600 ms
Jan 20 01:09:42.86: [ 3611]: MODEM set DTR ON
Jan 20 01:09:42.86: [ 3611]: MODEM set baud rate: 38400 baud, input flow

RTS/CTS, output flow RTS/CTS
Jan 20 01:09:42.86: [ 3611]: MODEM flush i/o
Jan 20 01:09:42.86: [ 3611]: <-- [15:ATE0V1Q0S0=0H0\r]
Jan 20 01:09:42.91: [ 3611]: --> [14:ATE0V1Q0S0=0H0]
Jan 20 01:09:42.91: [ 3611]: --> [2:OK]
Jan 20 01:09:42.91: [ 3611]: <-- [21:ATS8=2S7=60\Q3&D3&C1\r]
Jan 20 01:09:42.96: [ 3611]: --> [2:OK]
Jan 20 01:09:42.96: [ 3611]: <-- [12:AT+FCLASS=1\r]
Jan 20 01:09:42.97: [ 3611]: --> [2:OK]
Jan 20 01:09:42.97: [ 3611]: <-- [7:ATL0M1\r]
Jan 20 01:09:42.98: [ 3611]: --> [2:OK]
Jan 20 01:09:42.98: [ 3611]: MODEM input buffering enabled
Jan 20 01:09:42.98: [ 3611]: <-- [12:AT+FCLASS=1\r]
Jan 20 01:09:43.10: [ 3611]: --> [2:OK]
Jan 20 01:09:43.14: [ 3611]: DIAL 02418888313
Jan 20 01:09:43.14: [ 3611]: <-- [16:ATDT02418888313\r]
Jan 20 01:10:00.84: [ 3611]: --> [7:CONNECT]
Jan 20 01:10:00.84: [ 3611]: MODEM input buffering disabled
Jan 20 01:10:02.06: [ 3611]: --> [2:OK]
Jan 20 01:10:02.06: [ 3611]: <-- [9:AT+FRH=3\r]
Jan 20 01:10:02.08: [ 3611]: --> [7:CONNECT]
Jan 20 01:10:02.76: [ 3611]: --> [2:OK]
Jan 20 01:10:02.76: [ 3611]: REMOTE CSI "0241 8888313"
Jan 20 01:10:02.76: [ 3611]: <-- [9:AT+FRH=3\r]
Jan 20 01:10:02.77: [ 3611]: --> [7:CONNECT]

Jan 20 01:10:03.03: [ 3611]: --> [2:OK]
Jan 20 01:10:03.03: [ 3611]: REMOTE best rate 9600 bit/s
Jan 20 01:10:03.03: [ 3611]: REMOTE max page width 1728 pixels in 215 mm

Jan 20 01:10:03.03: [ 3611]: REMOTE max unlimited page length
Jan 20 01:10:03.03: [ 3611]: REMOTE best vres 7.7 line/mm
Jan 20 01:10:03.03: [ 3611]: REMOTE best format 2-D MMR
Jan 20 01:10:03.03: [ 3611]: REMOTE supports T.30 Annex A, ECM
Jan 20 01:10:03.03: [ 3611]: REMOTE best 20 ms, 10 ms/scanline
Jan 20 01:10:03.03: [ 3611]: USE 9600 bit/s
Jan 20 01:10:03.03: [ 3611]: USE 20 ms, 10 ms/scanline
Jan 20 01:10:03.03: [ 3611]: SEND file "docq/doc10.ps;41"
Jan 20 01:10:03.03: [ 3611]: USE page width 1728 pixels in 215 mm
Jan 20 01:10:03.03: [ 3611]: USE unlimited page length
Jan 20 01:10:03.03: [ 3611]: USE 7.7 line/mm
Jan 20 01:10:03.03: [ 3611]: USE 2-D MR
Jan 20 01:10:03.05: [ 3611]: SEND training at v.29 9600 bit/s
Jan 20 01:10:03.06: [ 3611]: <-- [9:AT+FTH=3\r]
Jan 20 01:10:03.09: [ 3611]: --> [7:CONNECT]
Jan 20 01:10:04.85: [ 3611]: --> [7:CONNECT]
Jan 20 01:10:05.42: [ 3611]: --> [2:OK]
Jan 20 01:10:05.42: [ 3611]: DELAY 75 ms
Jan 20 01:10:05.51: [ 3611]: <-- [10:AT+FTM=96\r]
Jan 20 01:10:05.79: [ 3611]: --> [7:CONNECT]
Jan 20 01:10:07.34: [ 3611]: --> [2:OK]
Jan 20 01:10:07.34: [ 3611]: <-- [9:AT+FRH=3\r]
Jan 20 01:10:07.62: [ 3611]: --> [7:CONNECT]
Jan 20 01:10:08.72: [ 3611]: --> [2:OK]
Jan 20 01:10:08.72: [ 3611]: TRAINING succeeded
Jan 20 01:10:08.72: [ 3611]: <-- [10:AT+FTM=96\r]
Jan 20 01:10:09.00: [ 3611]: --> [7:CONNECT]
Jan 20 01:10:09.00: [ 3611]: SEND begin page
Jan 20 01:10:22.53: [ 3611]: SENT 24973 bytes of data
Jan 20 01:10:22.53: [ 3611]: SEND 2D RTC
Jan 20 01:10:22.53: [ 3611]: SEND end page
Jan 20 01:10:29.89: [ 3611]: --> [2:OK]
Jan 20 01:10:29.89: [ 3611]: DELAY 95 ms
Jan 20 01:10:30.00: [ 3611]: SEND send EOP (no more pages or documents)
Jan 20 01:10:30.00: [ 3611]: <-- [9:AT+FTH=3\r]
Jan 20 01:10:30.03: [ 3611]: --> [7:CONNECT]
Jan 20 01:10:31.42: [ 3611]: --> [2:OK]
Jan 20 01:10:31.42: [ 3611]: <-- [9:AT+FRH=3\r]
Jan 20 01:10:34.52: [ 3611]: --> [0:]
Jan 20 01:10:34.52: [ 3611]: MODEM <Empty line>
Jan 20 01:10:34.52: [ 3611]: MODEM TIMEOUT: waiting for v.21 carrier
Jan 20 01:10:34.53: [ 3611]: --> [2:OK]
Jan 20 01:10:34.53: [ 3611]: SEND send EOP (no more pages or documents)
Jan 20 01:10:34.53: [ 3611]: <-- [9:AT+FTH=3\r]
Jan 20 01:10:34.56: [ 3611]: --> [7:CONNECT]
Jan 20 01:10:35.95: [ 3611]: --> [2:OK]
Jan 20 01:10:35.95: [ 3611]: <-- [9:AT+FRH=3\r]
Jan 20 01:10:39.05: [ 3611]: --> [0:]
Jan 20 01:10:39.05: [ 3611]: MODEM <Empty line>
Jan 20 01:10:39.05: [ 3611]: MODEM TIMEOUT: waiting for v.21 carrier
Jan 20 01:10:39.06: [ 3611]: --> [2:OK]
Jan 20 01:10:39.06: [ 3611]: SEND send EOP (no more pages or documents)
Jan 20 01:10:39.06: [ 3611]: <-- [9:AT+FTH=3\r]
Jan 20 01:10:39.09: [ 3611]: --> [7:CONNECT]
Jan 20 01:10:40.48: [ 3611]: --> [2:OK]
Jan 20 01:10:40.48: [ 3611]: <-- [9:AT+FRH=3\r]
Jan 20 01:10:43.58: [ 3611]: --> [0:]
Jan 20 01:10:43.58: [ 3611]: MODEM <Empty line>
Jan 20 01:10:43.58: [ 3611]: MODEM TIMEOUT: waiting for v.21 carrier
Jan 20 01:10:43.59: [ 3611]: --> [2:OK]
Jan 20 01:10:43.59: [ 3611]: <-- [9:AT+FTH=3\r]
Jan 20 01:10:43.62: [ 3611]: --> [7:CONNECT]
Jan 20 01:10:45.01: [ 3611]: --> [2:OK]
Jan 20 01:10:45.01: [ 3611]: MODEM input buffering enabled
Jan 20 01:10:45.01: [ 3611]: <-- [5:ATH0\r]
Jan 20 01:10:45.15: [ 3611]: --> [2:OK]
Jan 20 01:10:45.15: [ 3611]: MODEM set DTR OFF
Jan 20 01:10:45.15: [ 3611]: SESSION END

This is independent of the fax to send.
What is happening? Faxing to other faximiles is ok!

Hopefully waiting

Norbert Lesch