HylaFAX The world's most advanced open source fax server |
Wel, I had a look at the logfile. The log clearly says two pages have been send, the connection terminated normally. So according to the log everything is as it should be. --- log file ; cut here --- Jan 10 13:44:29.84: [ 1421]: SESSION BEGIN 00000002 32016053833512 Jan 10 13:44:29.84: [ 1421]: SEND FAX: JOB 1 DEST 053833512 COMMID 00000002 Jan 10 13:44:29.84: [ 1421]: DELAY 2600 ms Jan 10 13:44:32.45: [ 1421]: <-- [17:ATE0V1Q0X4S0=0H0\r] Jan 10 13:44:32.58: [ 1421]: --> [2:OK] Jan 10 13:44:32.58: [ 1421]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=1&D2&C1\r] Jan 10 13:44:32.72: [ 1421]: --> [2:OK] Jan 10 13:44:32.72: [ 1421]: <-- [14:AT+FCLASS=2.0\r] Jan 10 13:44:32.86: [ 1421]: --> [2:OK] Jan 10 13:44:32.86: [ 1421]: <-- [9:AT+FLO=2\r] Jan 10 13:44:33.00: [ 1421]: --> [2:OK] Jan 10 13:44:33.00: [ 1421]: <-- [9:AT+FPP=0\r] Jan 10 13:44:33.14: [ 1421]: --> [2:OK] Jan 10 13:44:33.14: [ 1421]: <-- [9:AT+FBO=0\r] Jan 10 13:44:33.28: [ 1421]: --> [2:OK] Jan 10 13:44:33.28: [ 1421]: <-- [10:AT+FCT=30\r] Jan 10 13:44:33.42: [ 1421]: --> [2:OK] Jan 10 13:44:33.42: [ 1421]: <-- [15:AT+FNR=1,1,1,1\r] Jan 10 13:44:33.56: [ 1421]: --> [2:OK] Jan 10 13:44:33.56: [ 1421]: <-- [9:AT+FIE=0\r] Jan 10 13:44:33.70: [ 1421]: --> [2:OK] Jan 10 13:44:33.70: [ 1421]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r] Jan 10 13:44:33.84: [ 1421]: --> [2:OK] Jan 10 13:44:33.84: [ 1421]: <-- [5:ATM0\r] Jan 10 13:44:33.97: [ 1421]: --> [2:OK] Jan 10 13:44:33.98: [ 1421]: <-- [14:AT+FCLASS=2.0\r] Jan 10 13:44:34.21: [ 1421]: --> [2:OK] Jan 10 13:44:34.21: [ 1421]: <-- [9:AT+FLO=2\r] Jan 10 13:44:34.45: [ 1421]: --> [2:OK] Jan 10 13:44:34.45: [ 1421]: <-- [9:AT+FPP=0\r] Jan 10 13:44:34.69: [ 1421]: --> [2:OK] Jan 10 13:44:34.69: [ 1421]: <-- [9:AT+FBO=0\r] Jan 10 13:44:34.93: [ 1421]: --> [2:OK] Jan 10 13:44:34.93: [ 1421]: <-- [10:AT+FCT=30\r] Jan 10 13:44:35.17: [ 1421]: --> [2:OK] Jan 10 13:44:35.17: [ 1421]: <-- [15:AT+FNR=1,1,1,1\r] Jan 10 13:44:35.41: [ 1421]: --> [2:OK] Jan 10 13:44:35.41: [ 1421]: <-- [9:AT+FIE=0\r] Jan 10 13:44:35.65: [ 1421]: --> [2:OK] Jan 10 13:44:35.65: [ 1421]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r] Jan 10 13:44:35.89: [ 1421]: --> [2:OK] Jan 10 13:44:35.89: [ 1421]: <-- [22:AT+FLI="NothingSetup"\r] Jan 10 13:44:36.13: [ 1421]: --> [2:OK] Jan 10 13:44:36.16: [ 1421]: DIAL 053833512 Jan 10 13:44:36.16: [ 1421]: <-- [14:ATDT053833512\r] Jan 10 13:44:51.48: [ 1421]: --> [4:+FCO] Jan 10 13:44:54.86: [ 1421]: --> [17:02020202020202003] Jan 10 13:44:54.86: [ 1421]: --> [27:+FCI:" 053833512"] Jan 10 13:44:54.86: [ 1421]: REMOTE CSI "053833512" Jan 10 13:44:54.87: [ 1421]: --> [20:+FIS:1,3,0,2,1,0,0,4] Jan 10 13:44:54.87: [ 1421]: --> [2:OK] Jan 10 13:44:54.87: [ 1421]: REMOTE best rate 9600 bit/s Jan 10 13:44:54.87: [ 1421]: REMOTE max page width 1728 pixels in 215 mm Jan 10 13:44:54.87: [ 1421]: REMOTE max unlimited page length Jan 10 13:44:54.87: [ 1421]: REMOTE best vres 7.7 line/mm Jan 10 13:44:54.87: [ 1421]: REMOTE best format 2-D MR Jan 10 13:44:54.87: [ 1421]: REMOTE best 20 ms, 10 ms/scanline Jan 10 13:44:54.87: [ 1421]: USE 9600 bit/s Jan 10 13:44:54.87: [ 1421]: USE 20 ms, 10 ms/scanline Jan 10 13:44:54.87: [ 1421]: SEND file "docq/doc1.cover;30" Jan 10 13:44:54.87: [ 1421]: USE page width 1728 pixels in 215 mm Jan 10 13:44:54.87: [ 1421]: USE unlimited page length Jan 10 13:44:54.87: [ 1421]: USE 3.85 line/mm Jan 10 13:44:54.87: [ 1421]: USE 1-D MR Jan 10 13:44:54.87: [ 1421]: <-- [23:AT+FIS=0,3,0,2,0,0,0,4\r] Jan 10 13:44:55.11: [ 1421]: --> [2:OK] Jan 10 13:44:55.11: [ 1421]: <-- [7:AT+FDT\r] Jan 10 13:44:55.38: [ 1421]: --> [20:+FCS:0,3,0,2,0,0,0,4] Jan 10 13:45:01.81: [ 1421]: --> [7:CONNECT] Jan 10 13:45:01.81: [ 1421]: SEND begin page Jan 10 13:45:01.82: [ 1421]: <-- data [1033] Jan 10 13:45:01.82: [ 1421]: <-- data [1032] Jan 10 13:45:01.82: [ 1421]: <-- data [1028] Jan 10 13:45:01.82: [ 1421]: <-- data [1045] Jan 10 13:45:02.82: [ 1421]: <-- data [1027] Jan 10 13:45:02.82: [ 1421]: <-- data [1048] Jan 10 13:45:02.82: [ 1421]: <-- data [1038] Jan 10 13:45:02.82: [ 1421]: <-- data [1057] Jan 10 13:45:03.80: [ 1421]: <-- data [1049] Jan 10 13:45:04.85: [ 1421]: <-- data [1056] Jan 10 13:45:05.90: [ 1421]: <-- data [1047] Jan 10 13:45:06.95: [ 1421]: <-- data [1040] Jan 10 13:45:06.95: [ 1421]: <-- data [1024] Jan 10 13:45:08.00: [ 1421]: <-- data [217] Jan 10 13:45:08.00: [ 1421]: SENT 13529 bytes of data Jan 10 13:45:08.00: [ 1421]: SEND 1D RTC Jan 10 13:45:08.00: [ 1421]: <-- data [9] Jan 10 13:45:08.00: [ 1421]: SEND end page Jan 10 13:45:08.00: [ 1421]: SEND send MPS (more pages, same document) Jan 10 13:45:08.00: [ 1421]: <-- data [2] Jan 10 13:45:20.34: [ 1421]: --> [2:OK] Jan 10 13:45:20.34: [ 1421]: SEND recv MCF (message confirmation) Jan 10 13:45:20.35: [ 1421]: SEND FAX (00000002): FROM bavo@beethoven.local.be TO 053833512 (page 1 of 2 sent in 0:26) Jan 10 13:45:20.35: [ 1421]: SEND FAX (00000002): FROM bavo@beethoven.local.be TO 053833512 (docq/doc1.cover;30 sent in 0:26) Jan 10 13:45:20.35: [ 1421]: SEND file "docq/doc1.ps;30" Jan 10 13:45:20.35: [ 1421]: USE page width 1728 pixels in 215 mm Jan 10 13:45:20.35: [ 1421]: USE unlimited page length Jan 10 13:45:20.35: [ 1421]: USE 3.85 line/mm Jan 10 13:45:20.35: [ 1421]: USE 1-D MR Jan 10 13:45:20.35: [ 1421]: <-- [7:AT+FDT\r] Jan 10 13:45:20.79: [ 1421]: --> [7:CONNECT] Jan 10 13:45:20.79: [ 1421]: SEND begin page Jan 10 13:45:20.80: [ 1421]: <-- data [1028] Jan 10 13:45:20.80: [ 1421]: <-- data [1028] Jan 10 13:45:20.80: [ 1421]: <-- data [1028] Jan 10 13:45:20.80: [ 1421]: <-- data [192] Jan 10 13:45:20.80: [ 1421]: SENT 3263 bytes of data Jan 10 13:45:20.80: [ 1421]: SEND 1D RTC Jan 10 13:45:20.80: [ 1421]: <-- data [9] Jan 10 13:45:20.80: [ 1421]: SEND end page Jan 10 13:45:20.80: [ 1421]: SEND send EOP (no more pages or documents) Jan 10 13:45:20.80: [ 1421]: <-- data [2] Jan 10 13:45:28.15: [ 1421]: --> [7:+FHS:00] Jan 10 13:45:28.15: [ 1421]: REMOTE HANGUP: Normal and proper end of connection (code 0) Jan 10 13:45:28.15: [ 1421]: SEND recv MCF (message confirmation) Jan 10 13:45:28.16: [ 1421]: SEND FAX (00000002): FROM bavo@beethoven.local.be TO 053833512 (page 2 of 2 sent in 0:08) Jan 10 13:45:28.16: [ 1421]: SEND FAX (00000002): FROM bavo@beethoven.local.be TO 053833512 (docq/doc1.ps;30 sent in 0:08) Jan 10 13:45:28.16: [ 1421]: <-- [5:ATH0\r] Jan 10 13:45:28.27: [ 1421]: --> [2:OK] Jan 10 13:45:28.28: [ 1421]: SESSION END --- cut here --- I use the RPM hylafax distribution (hylafax-4_0-7_i386.rpm) on redhat 5.2 Modem: US Robotics Sportster Voice 33.6 external. Since this "failure" every outbound and inbound fax was processed correctly, on both sides. Bavo De Ridder On Sun, 10 Jan 1999, you wrote: >At 14:06 10/01/99 +0100, Bavo De Ridder wrote: >>Hello, >> >>Whenever I use faxmail to send an email to a faxmachine, only the coverpage >>is received. Although the coverpage mentions "1 sheet to follow", no sheet >>follows. Off course, the body if the mail is on the next sheet. What is >>going wrong (and is something going wrong...). >> > >Have a look in the log directory in the fax spool directory. On my >system this is /var/spool/fax/log. The files in there ( cXXXXXX type) >are a text file of the fax session. Have a look at them, if it is not >obvious to you what the problem is, reply to the mailing list containing >a log along with the distribution of HylaFAX you are using, the system you >are running on and your modem. > >Cheers, >Phil Watkinson, >Boston, UK.