flexfax: Problems receiving faxes

[Andreas Mock <AMock@osram.com>]

Hallo together!

I just installed HylaFAX v4.0pl2-12 under SuSE-Linux 5.3
Kernel 2.0.34.

A Creatix SG2834 Turbo is attached to /dev/cua1.
It is detected as ROCKWELL AC/V34/V1.510-V34_DS

The whole installation went through straight forward.

Now I can send faxes without problems and can
receive faxes. If faxgetty receives a fax, the
log seems normal, but the contrahent who sends the
fax is always claiming about a mistake. One fax I
tried said that there was an incorrect acknowledgement
of the fax-message. 
The fax document I received is complete and I can
convert it to different formats.
I really don't know what is the reason for all sender
faxes claiming about an error.

Attached is a session log of receiving a fax.

Thank you in advance
Andreas Mock


Dec 08 12:41:25.14: [27662]: SESSION BEGIN 00000040 49732412446
Dec 08 12:41:25.14: [27662]: <-- [4:ATA\r]
Dec 08 12:41:33.67: [27662]: --> [5:+FCON]
Dec 08 12:41:33.67: [27662]: MODEM set baud rate: 19200 baud (flow
control uncha
Dec 08 12:41:33.67: [27662]: MODEM set baud rate: 19200 baud, input flow
XON/XOF
Dec 08 12:41:33.67: [27662]: ANSWER: FAX CONNECTION
Dec 08 12:41:33.67: [27662]: MODEM input buffering enabled
Dec 08 12:41:33.67: [27662]: RECV FAX: begin
Dec 08 12:41:35.28: [27662]: --> [29:+FTSI: "     +49 89 62133449"]
Dec 08 12:41:35.28: [27662]: REMOTE TSI "+49 89 62133449"
Dec 08 12:41:35.58: [27662]: --> [22:+FDCS: 0,5,0,2,1,0,0,1]
Dec 08 12:41:35.58: [27662]: REMOTE wants 14400 bit/s
Dec 08 12:41:35.58: [27662]: REMOTE wants page width 1728 pixels in 215
mm
Dec 08 12:41:35.58: [27662]: REMOTE wants unlimited page length
Dec 08 12:41:35.58: [27662]: REMOTE wants 3.85 line/mm
Dec 08 12:41:35.58: [27662]: REMOTE wants 2-D MR
Dec 08 12:41:35.69: [27662]: --> [2:OK]
Dec 08 12:41:35.69: [27662]: <-- [7:AT+FDR\r]
Dec 08 12:41:38.59: [27662]: --> [5:+FCFR]
Dec 08 12:41:41.12: [27662]: --> [22:+FDCS: 0,5,0,2,1,0,0,1]
Dec 08 12:41:41.12: [27662]: REMOTE wants 14400 bit/s
Dec 08 12:41:41.12: [27662]: REMOTE wants page width 1728 pixels in 215
mm
Dec 08 12:41:41.12: [27662]: REMOTE wants unlimited page
length              
Dec 08 12:41:41.12: [27662]: REMOTE wants 3.85 line/mm
Dec 08 12:41:41.12: [27662]: REMOTE wants 2-D MR
Dec 08 12:41:41.12: [27662]: --> [7:CONNECT]
Dec 08 12:41:41.12: [27662]: RECV: begin page
Dec 08 12:41:41.12: [27662]: MODEM set XON/XOFF/FLUSH: input ignored,
output gen
Dec 08 12:41:41.12: [27662]: RECV: send trigger 022
Dec 08 12:41:41.12: [27662]: <-- data [1]
Dec 08 12:41:47.56: [27662]: RECV: 1118 total lines, 0 bad lines, 0
consecutive
Dec 08 12:41:47.56: [27662]: MODEM set XON/XOFF/DRAIN: input
interpreted, output
Dec 08 12:41:47.56: [27662]: --> [17:+FPTS: 2,2219,0,0]
Dec 08 12:41:48.73: [27662]: --> [7:+FET: 2]
Dec 08 12:41:48.73: [27662]: RECV recv EOP (no more pages or documents)
Dec 08 12:41:48.84: [27662]: --> [2:OK]
Dec 08 12:41:48.86: [27662]: RECV send MCF (message confirmation)
Dec 08 12:41:48.86: [27662]: RECV FAX (00000040): from +49 89 62133449,
page 1 i
Dec 08 12:41:48.87: [27662]: RECV FAX (00000040): recvq/fax00018.tif
from +49 89
Dec 08 12:41:48.92: [27662]: <-- [7:AT+FDR\r]
Dec 08 12:41:52.15: [27662]: --> [8:+FHNG: 0]
Dec 08 12:41:52.15: [27662]: REMOTE HANGUP: Normal and proper end of
connection
Dec 08 12:41:52.15: [27662]: RECV FAX: bin/faxrcvd "recvq/fax00018.tif"
"cua1" "
Dec 08 12:41:53.94: [27662]: RECV FAX: end
Dec 08 12:41:53.94: [27662]: SESSION END