HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

Problems talking to certain fax machines ...





Hi,

I've had a look through the FAQ and while I found several answers about
this sort of problem I didn't see anything about the specific error I'm
getting so I was wondering if anyone here could help.

I'm running hylafax v4.0pl2 on a SCO OSR5 box and i'm getting the
following log file.

> Nov 16 13:59:56.15: [ 2942]: SESSION BEGIN 00000061 4411601162567444
> Nov 16 13:59:56.15: [ 2942]: SEND FAX: JOB 57 DEST 01162567444 COMMID
> 00000061
> Nov 16 13:59:56.15: [ 2942]: MODEM set DTR OFF
> Nov 16 13:59:56.15: [ 2942]: MODEM set baud rate: 0 baud (flow control
> unchanged)
> Nov 16 13:59:56.40: [ 2942]: DELAY 2600 ms
> Nov 16 13:59:59.01: [ 2942]: MODEM set DTR ON
> Nov 16 13:59:59.13: [ 2942]: MODEM set baud rate: 19200 baud, input
> flow XON/XOFF, output flow XON/XOFF
> Nov 16 13:59:59.13: [ 2942]: MODEM flush i/o
> Nov 16 13:59:59.13: [ 2942]: <-- [15:ATE0V1Q0S0=0H0\r]
> Nov 16 13:59:59.16: [ 2942]: --> [2:OK]
> Nov 16 13:59:59.16: [ 2942]: <-- [21:ATS8=2S7=60&K4&D2&C1\r]
> Nov 16 13:59:59.19: [ 2942]: --> [2:OK]
> Nov 16 13:59:59.19: [ 2942]: <-- [12:AT+FCLASS=1\r]
> Nov 16 13:59:59.22: [ 2942]: --> [2:OK]
> Nov 16 13:59:59.22: [ 2942]: <-- [5:ATM0\r]
> Nov 16 13:59:59.24: [ 2942]: --> [2:OK]
> Nov 16 13:59:59.24: [ 2942]: MODEM input buffering enabled
> Nov 16 13:59:59.24: [ 2942]: <-- [12:AT+FCLASS=1\r]
> Nov 16 13:59:59.36: [ 2942]: --> [2:OK]
> Nov 16 13:59:59.37: [ 2942]: MODEM set XON/XOFF/FLUSH: input ignored,
> output disabled
> Nov 16 13:59:59.39: [ 2942]: DIAL 01162567444
> Nov 16 13:59:59.39: [ 2942]: <-- [17:ATDT01162567444@\r]
> Nov 16 14:00:10.30: [ 2942]: --> [7:CONNECT]
> Nov 16 14:00:10.30: [ 2942]: MODEM input buffering disabled
> Nov 16 14:00:10.88: [ 2942]: --> HDLC<12:FF C0 04 B5 00 00 9E 86 FD 1A
> 2C CE>
> Nov 16 14:00:10.89: [ 2942]: --> [2:OK]
> Nov 16 14:00:10.89: [ 2942]: <-- [9:AT+FRH=3\r]
> Nov 16 14:00:10.92: [ 2942]: --> [7:CONNECT]
> Nov 16 14:00:11.87: [ 2942]: --> HDLC<34:FF C0 04 00 00 90 00 06 00 12
> 23 23 0F 17 19 23 0F 18 15 1C 20 14 15 23 1B 0F 0F 0F 0F 0F 00 00 4E
> 7D>
> Nov 16 14:00:11.88: [ 2942]: --> [2:OK]
> Nov 16 14:00:11.88: [ 2942]: <-- [9:AT+FRH=3\r]
> Nov 16 14:00:11.91: [ 2942]: --> [7:CONNECT]
> Nov 16 14:00:12.59: [ 2942]: --> HDLC<25:FF C0 02 04 04 04 04 04 04 04
> 04 04 2C 2C 2C EC 6C AC 4C 6C 8C 8C 0C BD EA>
> Nov 16 14:00:12.60: [ 2942]: --> [2:OK]
> Nov 16 14:00:12.60: [ 2942]: REMOTE CSI "01162567444"
> Nov 16 14:00:12.60: [ 2942]: <-- [9:AT+FRH=3\r]
> Nov 16 14:00:12.63: [ 2942]: --> [7:CONNECT]
> Nov 16 14:00:12.88: [ 2942]: --> HDLC<9:FF C8 01 00 73 1D 20 62 76>
> Nov 16 14:00:12.89: [ 2942]: --> [2:OK]
> Nov 16 14:00:12.89: [ 2942]: REMOTE best rate 9600 bit/s
> Nov 16 14:00:12.89: [ 2942]: REMOTE max page width 1728 pixels in 215
> mm
> Nov 16 14:00:12.89: [ 2942]: REMOTE max unlimited page length 
> Nov 16 14:00:12.89: [ 2942]: REMOTE best vres 7.7 line/mm
> Nov 16 14:00:12.89: [ 2942]: REMOTE best format 2-D MR
> Nov 16 14:00:12.89: [ 2942]: REMOTE supports T.30 Annex A, ECM
> Nov 16 14:00:12.89: [ 2942]: REMOTE best 20 ms, 10 ms/scanline
> Nov 16 14:00:12.89: [ 2942]: USE 9600 bit/s
> Nov 16 14:00:12.89: [ 2942]: USE 20 ms, 10 ms/scanline
> Nov 16 14:00:12.89: [ 2942]: SEND file "docq/doc57.cover;40"
> Nov 16 14:00:12.89: [ 2942]: USE page width 1728 pixels in 215 mm
> Nov 16 14:00:12.89: [ 2942]: USE unlimited page length 
> Nov 16 14:00:12.89: [ 2942]: USE 3.85 line/mm
> Nov 16 14:00:12.89: [ 2942]: USE 2-D MR
> Nov 16 14:00:12.89: [ 2942]: SEND training at v.29 9600 bit/s
> Nov 16 14:00:12.89: [ 2942]: <-- [9:AT+FTH=3\r]
> Nov 16 14:00:12.95: [ 2942]: --> [7:CONNECT]
> Nov 16 14:00:12.95: [ 2942]: <-- HDLC<23:FF C0 C2 B6 A6 2E CE 9E CE 04
> 1E 86 62 04 CA CA 42 04 04 04 04 04 04>
> Nov 16 14:00:14.74: [ 2942]: --> [7:CONNECT]
> Nov 16 14:00:14.74: [ 2942]: <-- HDLC<6:FF C8 C1 00 61 10>
> Nov 16 14:00:15.18: [ 2942]: --> [2:OK]
> Nov 16 14:00:15.18: [ 2942]: DELAY 75 ms
> Nov 16 14:00:15.27: [ 2942]: MODEM set XON/XOFF/FLUSH: input
> interpreted, output disabled
> Nov 16 14:00:15.29: [ 2942]: <-- [10:AT+FTM=96\r]
> Nov 16 14:00:15.36: [ 2942]: --> [7:CONNECT]
> Nov 16 14:00:17.32: [ 2942]: --> [2:OK]
> Nov 16 14:00:17.32: [ 2942]: MODEM set XON/XOFF/DRAIN: input ignored,
> output disabled
> Nov 16 14:00:17.34: [ 2942]: <-- [9:AT+FRH=3\r]
> Nov 16 14:00:17.74: [ 2942]: --> [7:CONNECT]
> Nov 16 14:00:18.47: [ 2942]: --> HDLC<5:FF C8 5F C8 E7>
> Nov 16 14:00:18.47: [ 2942]: --> [2:OK]
> Nov 16 14:00:18.47: [ 2942]: TRAINING failed
> Nov 16 14:00:18.47: [ 2942]: SEND: RSRPEC error/got DCN; Giving up
> after 3 attempts to send same page "docq/doc57.cover;40", dirnum 0
> Nov 16 14:00:18.47: [ 2942]: <-- [9:AT+FTH=3\r]
> Nov 16 14:00:18.53: [ 2942]: --> [7:CONNECT]
> Nov 16 14:00:18.53: [ 2942]: <-- HDLC<3:FF C8 DF>
> Nov 16 14:00:19.84: [ 2942]: --> [2:OK]
> Nov 16 14:00:19.84: [ 2942]: MODEM input buffering enabled
> Nov 16 14:00:19.84: [ 2942]: <-- [5:ATH0\r]
> Nov 16 14:00:20.54: [ 2942]: --> [2:OK]
> Nov 16 14:00:20.54: [ 2942]: MODEM set DTR OFF
> Nov 16 14:00:20.54: [ 2942]: MODEM set baud rate: 0 baud (flow control
> unchanged)
> Nov 16 14:00:20.91: [ 2942]: SESSION END

Any ideas ...
Lee.
-- 
I was doing object-oriented assembly at 1 year old ...  
For some reason my mom insists on calling it "Playing with blocks"




Project hosted by iFAX Solutions