Re: flexfax: Faxes curupt

[Damian Ivereigh <damian@cisco.com>]

Hi Andrew,

Andrew Williams wrote:

> > > I'm having a problem with my sent faxes.
> > > I'm using hylafax4.0pl2-3 rpm on RH5.0.
> > >
> > > Whenever i send a fax it comes out on the other end about four inches
> > > per page making it unusable.
> > >
> > > I preview the faxes before i send and all seems fine but no matter what
> > > i do i cant seem to fix this problem.
> > >
> > > I finally got hylafax working on my system except for this one thing.
> > > Any help would be appreciated.
>
> I'm sorry, here is the log for one of the faxes.
> 
> Oct 12 20:10:36.36: [  393]: SESSION BEGIN 00000002 19736725112
> Oct 12 20:10:36.36: [  393]: SEND FAX: JOB 1 DEST 6725112 COMMID
> 00000002
> Oct 12 20:10:36.36: [  393]: DELAY 2600 ms
> Oct 12 20:10:38.97: [  393]: <-- [15:ATE0V1Q0S0=0H0\r]
> Oct 12 20:10:39.02: [  393]: --> [2:OK]
> Oct 12 20:10:39.02: [  393]: <-- [12:ATS8=2S7=60\r]
> Oct 12 20:10:39.08: [  393]: --> [2:OK]
> Oct 12 20:10:39.08: [  393]: <-- [12:AT+FCLASS=2\r]
> Oct 12 20:10:39.12: [  393]: --> [2:OK]
> Oct 12 20:10:39.12: [  393]: <-- [10:AT+FTBC=0\r]
> Oct 12 20:10:39.16: [  393]: --> [2:OK]
> Oct 12 20:10:39.16: [  393]: <-- [10:AT+FBOR=0\r]
> Oct 12 20:10:39.21: [  393]: --> [2:OK]
> Oct 12 20:10:39.21: [  393]: <-- [13:AT+FPHCTO=30\r]
> Oct 12 20:10:39.26: [  393]: --> [2:OK]
> Oct 12 20:10:39.26: [  393]: <-- [24:AT+FDCC=1,5,0,2,0,0,0,0\r]
> Oct 12 20:10:39.31: [  393]: --> [2:OK]
> Oct 12 20:10:39.31: [  393]: <-- [5:ATM0\r]
> Oct 12 20:10:39.35: [  393]: --> [2:OK]
> Oct 12 20:10:39.35: [  393]: <-- [12:AT+FCLASS=2\r]
> Oct 12 20:10:39.49: [  393]: --> [2:OK]
> Oct 12 20:10:39.49: [  393]: <-- [10:AT+FTBC=0\r]
> Oct 12 20:10:39.63: [  393]: --> [2:OK]
> Oct 12 20:10:39.63: [  393]: <-- [10:AT+FBOR=0\r]
> Oct 12 20:10:39.77: [  393]: --> [2:OK]
> Oct 12 20:10:39.77: [  393]: <-- [13:AT+FPHCTO=30\r]
> Oct 12 20:10:39.91: [  393]: --> [2:OK]
> Oct 12 20:10:39.91: [  393]: <-- [24:AT+FDCC=1,5,0,2,0,0,0,0\r]
> Oct 12 20:10:40.06: [  393]: --> [2:OK]
> Oct 12 20:10:40.06: [  393]: <-- [23:AT+FLID="NothingSetup"\r]
> Oct 12 20:10:40.21: [  393]: --> [2:OK]
> Oct 12 20:10:40.51: [  393]: DIAL 6725111
> Oct 12 20:10:40.51: [  393]: <-- [12:ATDT6725112\r]
> Oct 12 20:10:56.19: [  393]: --> [5:+FCON]
> Oct 12 20:10:57.53: [  393]: --> [54:+FNSF:00 00 56 55 55 00 80 B0 80 00
> 00 59 D4 04 07 05 ]
> Oct 12 20:10:57.53: [  393]: REMOTE NSF "00 00 56 55 55 00 80 B0 80 00
> 00 59 D4 04 07 05"
> Oct 12 20:10:58.21: [  393]: --> [28:+FCSI:"          9736725112"]
> Oct 12 20:10:58.21: [  393]: REMOTE CSI "9736725112"
> Oct 12 20:10:58.56: [  393]: --> [21:+FDIS:1,3,0,2,0,0,0,4]
> Oct 12 20:10:58.56: [  393]: --> [2:OK]
> Oct 12 20:10:58.56: [  393]: REMOTE best rate 9600 bit/s
> Oct 12 20:10:58.56: [  393]: REMOTE max page width 1728 pixels in 215 mm
> Oct 12 20:10:58.56: [  393]: REMOTE max unlimited page length
> Oct 12 20:10:58.56: [  393]: REMOTE best vres 7.7 line/mm
> Oct 12 20:10:58.56: [  393]: REMOTE best format 1-D MR
> Oct 12 20:10:58.56: [  393]: REMOTE best 20 ms, 10 ms/scanline
> Oct 12 20:10:58.56: [  393]: USE 9600 bit/s
> Oct 12 20:10:58.56: [  393]: USE 20 ms, 10 ms/scanline
> Oct 12 20:10:58.56: [  393]: SEND file "docq/doc1.cover;31"
> Oct 12 20:10:58.56: [  393]: USE page width 1728 pixels in 215 mm
> Oct 12 20:10:58.56: [  393]: USE unlimited page length
> Oct 12 20:10:58.56: [  393]: USE 7.7 line/mm
> Oct 12 20:10:58.56: [  393]: USE 1-D MR
> Oct 12 20:10:58.56: [  393]: <-- [7:AT+FDT\r]
> Oct 12 20:11:05.05: [  393]: --> [21:+FDCS:1,3,0,2,0,0,0,4]
> Oct 12 20:11:05.05: [  393]: --> [7:CONNECT]
> Oct 12 20:11:05.05: [  393]: SEND wait for XON
> Oct 12 20:11:05.05: [  393]: --> [1:]
> Oct 12 20:11:05.05: [  393]: SEND begin page
> Oct 12 20:11:05.05: [  393]: <-- data [1027]
> Oct 12 20:11:05.05: [  393]: <-- data [1028]
> Oct 12 20:11:05.05: [  393]: <-- data [1032]
> Oct 12 20:11:05.05: [  393]: <-- data [1036]
> Oct 12 20:11:07.05: [  393]: <-- data [1031]
> Oct 12 20:11:07.05: [  393]: <-- data [1025]
> Oct 12 20:11:07.05: [  393]: <-- data [1037]
> Oct 12 20:11:07.05: [  393]: <-- data [1054]
> Oct 12 20:11:09.04: [  393]: <-- data [1026]
> Oct 12 20:11:09.04: [  393]: <-- data [1033]
> Oct 12 20:11:09.04: [  393]: <-- data [1056]
> Oct 12 20:11:09.05: [  393]: <-- data [1043]
> Oct 12 20:11:11.04: [  393]: <-- data [1049]
> Oct 12 20:11:11.04: [  393]: <-- data [1064]
> Oct 12 20:11:11.04: [  393]: <-- data [1059]
> Oct 12 20:11:11.04: [  393]: <-- data [1039]
> Oct 12 20:11:13.04: [  393]: <-- data [1059]
> Oct 12 20:11:13.04: [  393]: <-- data [1050]
> Oct 12 20:11:13.04: [  393]: <-- data [1035]
> Oct 12 20:11:15.03: [  393]: <-- data [1037]
> Oct 12 20:11:15.03: [  393]: <-- data [1048]
> Oct 12 20:11:15.03: [  393]: <-- data [1035]
> Oct 12 20:11:15.03: [  393]: <-- data [1027]
> Oct 12 20:11:17.03: [  393]: <-- data [1024]
> Oct 12 20:11:17.03: [  393]: <-- data [916]
> Oct 12 20:11:17.03: [  393]: SENT 25492 bytes of data
> Oct 12 20:11:17.03: [  393]: <-- data [2]
> Oct 12 20:11:17.03: [  393]: SEND end page
> Oct 12 20:11:19.31: [  393]: -->
> [44:]
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Oooh. what's this?

> Oct 12 20:11:19.31: [  393]: --> [2:OK]
> Oct 12 20:11:19.31: [  393]: SEND send MPS (more pages, same document)
> Oct 12 20:11:19.31: [  393]: <-- [9:AT+FET=0\r]
> Oct 12 20:11:23.29: [  393]: --> [7:+FPTS:1]
> Oct 12 20:11:23.29: [  393]: --> [2:OK]
> Oct 12 20:11:23.29: [  393]: SEND recv MCF (message confirmation)
> Oct 12 20:11:23.29: [  393]: SEND FAX (00000002): FROM root@rasdomain TO
> 6725112 (page 1 of 2 sent in 0:25)
> Oct 12 20:11:23.29: [  393]: SEND FAX (00000002): FROM root@rasdomain TO
> 6725112 (docq/doc1.cover;31 sent in 0:25)

I hope this just your email client (correctly) wrapping the lines

> Oct 12 20:11:23.29: [  393]: SEND file "docq/doc1.ps;31"
> Oct 12 20:11:23.29: [  393]: USE page width 1728 pixels in 215 mm
> Oct 12 20:11:23.29: [  393]: USE unlimited page length
> Oct 12 20:11:23.29: [  393]: USE 7.7 line/mm
> Oct 12 20:11:23.29: [  393]: USE 1-D MR
> Oct 12 20:11:23.29: [  393]: <-- [7:AT+FDT\r]
> Oct 12 20:11:23.71: [  393]: --> [7:CONNECT]
> Oct 12 20:11:23.71: [  393]: SEND wait for XON
> Oct 12 20:11:23.71: [  393]: --> [1:]
> Oct 12 20:11:23.71: [  393]: SEND begin page
> Oct 12 20:11:23.71: [  393]: <-- data [1026]
> Oct 12 20:11:23.71: [  393]: <-- data [1030]
> Oct 12 20:11:23.71: [  393]: <-- data [1027]
> Oct 12 20:11:23.71: [  393]: <-- data [1026]
> Oct 12 20:11:23.71: [  393]: <-- data [1026]
> Oct 12 20:11:25.71: [  393]: <-- data [1024]
> Oct 12 20:11:25.71: [  393]: <-- data [1024]
> Oct 12 20:11:25.71: [  393]: <-- data [1025]
> Oct 12 20:11:27.70: [  393]: <-- data [1025]
> Oct 12 20:11:27.70: [  393]: <-- data [1025]
> Oct 12 20:11:27.70: [  393]: <-- data [1025]
> Oct 12 20:11:27.70: [  393]: <-- data [1025]
> Oct 12 20:11:29.70: [  393]: <-- data [1025]
> Oct 12 20:11:29.70: [  393]: <-- data [1036]
> Oct 12 20:11:29.70: [  393]: <-- data [1027]
> Oct 12 20:11:29.70: [  393]: <-- data [1024]
> Oct 12 20:11:31.70: [  393]: <-- data [1025]
> Oct 12 20:11:31.70: [  393]: <-- data [1025]
> Oct 12 20:11:31.70: [  393]: <-- data [1028]
> Oct 12 20:11:33.69: [  393]: <-- data [1027]
> Oct 12 20:11:33.69: [  393]: <-- data [1025]
> Oct 12 20:11:33.69: [  393]: <-- data [1026]
> Oct 12 20:11:33.69: [  393]: <-- data [1026]
> Oct 12 20:11:35.69: [  393]: <-- data [1029]
> Oct 12 20:11:35.69: [  393]: <-- data [1026]
> Oct 12 20:11:35.69: [  393]: <-- data [1026]
> Oct 12 20:11:35.69: [  393]: <-- data [1026]
> Oct 12 20:11:37.69: [  393]: <-- data [1024]
> Oct 12 20:11:37.69: [  393]: <-- data [1024]
> Oct 12 20:11:37.69: [  393]: <-- data [1024]
> Oct 12 20:11:37.69: [  393]: <-- data [1024]
> Oct 12 20:11:39.68: [  393]: <-- data [1024]
> Oct 12 20:11:39.68: [  393]: <-- data [1024]
> Oct 12 20:11:39.68: [  393]: <-- data [1024]
> Oct 12 20:11:41.68: [  393]: <-- data [1024]
> Oct 12 20:11:41.68: [  393]: <-- data [1025]
> Oct 12 20:11:41.68: [  393]: <-- data [1027]
> Oct 12 20:11:41.68: [  393]: <-- data [1027]
> Oct 12 20:11:43.68: [  393]: <-- data [701]
> Oct 12 20:11:43.68: [  393]: SENT 39613 bytes of data
> Oct 12 20:11:43.68: [  393]: <-- data [2]
> Oct 12 20:11:43.68: [  393]: SEND end page
> Oct 12 20:11:46.34: [  393]: -->
> [46:]
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Hmm more of the same.

> Oct 12 20:11:46.34: [  393]: --> [2:OK]
> Oct 12 20:11:46.34: [  393]: SEND send EOP (no more pages or documents)
> Oct 12 20:11:46.34: [  393]: <-- [9:AT+FET=2\r]
> Oct 12 20:11:50.34: [  393]: --> [7:+FPTS:1]
> Oct 12 20:11:50.34: [  393]: SEND recv MCF (message confirmation)
> Oct 12 20:11:50.34: [  393]: SEND FAX (00000002): FROM root@rasdomain TO
> 6725112 (page 2 of 2 sent in 0:27)
> Oct 12 20:11:50.34: [  393]: SEND FAX (00000002): FROM root@rasdomain TO
> 6725112 (docq/doc1.ps;31 sent in 0:27)
> Oct 12 20:11:50.34: [  393]: <-- [5:ATH0\r]
> Oct 12 20:11:51.79: [  393]: --> [7:+FHNG:0]
> Oct 12 20:11:51.79: [  393]: REMOTE HANGUP: Normal and proper end of
> connection (code 0)
> Oct 12 20:11:52.41: [  393]: --> [2:OK]
> Oct 12 20:11:52.41: [  393]: SESSION END

Is those wierd lines really in your log? If so there may be something
sick about your executable.

Anyone else have any better ideas?

Damian
 

-- 
 ______________________________________________________________________
* Damian Ivereigh     *      ||        ||      * Cisco Systems, Inc.   *
* MIS Printer Admin   *    .||||.    .||||.    * Sydney, Australia     *
* Linux Bigot         * ..:||||||:..:||||||:.. * +61 2 8448 7344       *
* damian@cisco.com    *   cisco Systems, Inc.  * Fax: +61 2 8448 7228  *
*______________________________________________________________________*