flexfax: Problems with sending fax

[Philipp Gruenig <gruenig@tecnosoft.ch>]

Hi

I've a problem with sending faxes with more than 1 page!

here is the log:

Apr 22 01:35:18.48: [15159]: REMOTE supports T.30 Annex A, ECM
Apr 22 01:35:18.48: [15159]: REMOTE best 10 ms/scanline
Apr 22 01:35:18.48: [15159]: USE 9600 bit/s
Apr 22 01:35:18.48: [15159]: USE 10 ms/scanline
Apr 22 01:35:18.48: [15159]: SEND file "docq/doc11.ps;40"
Apr 22 01:35:18.48: [15159]: USE page width 1728 pixels in 215 mm
Apr 22 01:35:18.48: [15159]: USE unlimited page length 
Apr 22 01:35:18.48: [15159]: USE 3.85 line/mm
Apr 22 01:35:18.48: [15159]: USE 2-D MR
Apr 22 01:35:18.48: [15159]: <-- [23:AT+FIS=0,3,0,2,1,0,0,3\r]
Apr 22 01:35:18.60: [15159]: --> [2:OK]
Apr 22 01:35:18.60: [15159]: <-- [7:AT+FDT\r]
Apr 22 01:35:24.50: [15159]: --> [20:+FCS:0,3,0,2,1,0,0,3]
Apr 22 01:35:24.50: [15159]: --> [7:CONNECT]
Apr 22 01:35:24.50: [15159]: SEND begin page
Apr 22 01:35:49.97: [15159]: SENT 33027 bytes of data
Apr 22 01:35:49.97: [15159]: SEND 2D RTC
Apr 22 01:35:49.97: [15159]: SEND end page
Apr 22 01:35:49.97: [15159]: SEND send MPS (more pages, same document)
Apr 22 01:36:00.82: [15159]: --> [5:ERROR]
Apr 22 01:36:00.82: [15159]: SEND recv RTN (retrain negative)
Apr 22 01:36:00.82: [15159]: <-- [7:AT+FDT\r]
Apr 22 01:36:06.73: [15159]: --> [20:+FCS:0,3,0,2,1,0,0,3]
Apr 22 01:36:06.73: [15159]: --> [7:CONNECT]
Apr 22 01:36:06.73: [15159]: SEND begin page
Apr 22 01:36:32.11: [15159]: SENT 33027 bytes of data
Apr 22 01:36:32.11: [15159]: SEND 2D RTC
Apr 22 01:36:32.11: [15159]: SEND end page
Apr 22 01:36:32.11: [15159]: SEND send MPS (more pages, same document)
Apr 22 01:36:43.06: [15159]: --> [5:ERROR]
Apr 22 01:36:43.06: [15159]: SEND recv RTN (retrain negative)
Apr 22 01:36:43.06: [15159]: <-- [7:AT+FDT\r]
Apr 22 01:36:49.00: [15159]: --> [20:+FCS:0,3,0,2,1,0,0,3]
Apr 22 01:36:49.00: [15159]: --> [7:CONNECT]
Apr 22 01:36:49.00: [15159]: SEND begin page
Apr 22 01:37:14.37: [15159]: SENT 33027 bytes of data
Apr 22 01:37:14.37: [15159]: SEND 2D RTC
Apr 22 01:37:14.37: [15159]: SEND end page
Apr 22 01:37:14.37: [15159]: SEND send MPS (more pages, same document)
Apr 22 01:37:25.32: [15159]: --> [5:ERROR]
Apr 22 01:37:25.32: [15159]: SEND recv RTN (retrain negative)
Apr 22 01:37:25.32: [15159]: <-- [7:AT+FKS\r]
Apr 22 01:37:26.83: [15159]: --> [7:+FHS:02]
Apr 22 01:37:26.83: [15159]: REMOTE HANGUP: Call aborted,  from +FK or
<CAN> (code 2)
Apr 22 01:37:26.83: [15159]: --> [5:ERROR]
Apr 22 01:37:26.83: [15159]: MODEM Command error
Apr 22 01:37:26.83: [15159]: <-- [5:ATH0\r]
Apr 22 01:37:27.22: [15159]: --> [10:NO CARRIER]
Apr 22 01:37:27.22: [15159]: MODEM No carrier
Apr 22 01:37:27.22: [15159]: SESSION END

Any ideas of my problem?
Thanks in advance for any tips.
We use FreeBSD 2.2.2 with HylaFax 4.0pl1
and a Zyxel Modem U 1496 E plus

Philipp Gruenig