flexfax: "FIS answer timeout" *or* "No response to MPS or EOP" errors for USR Courier v34d

[Gildas Perrot <perrot@francenet.fr>]

Hi, 

I am using hylafax v4.0pl1 on a BSD/OS 2.1 system with a USR Courier v34 Fax 
connected to it.

At the beginning, I was using Class2.0 but I had problem after FIS emission as 
shown below :

Nov 19 16:49:58.56: [20798]: SESSION BEGIN 00006313 X
Nov 19 16:49:58.56: [20798]: SEND FAX: JOB 4061 DEST X# COMMID 00006313
Nov 19 16:49:58.56: [20798]: DELAY 2600 ms
Nov 19 16:50:01.17: [20798]: <-- [17:ATE0V1Q0X4S0=0H0\r]
Nov 19 16:50:01.33: [20798]: --> [16:ATE0V1Q0X4S0=0H0]
Nov 19 16:50:01.33: [20798]: --> [2:OK]
Nov 19 16:50:01.33: [20798]: <-- [32:ATS8=2S7=60&H2&I2&R1S13=1&D2&C1\r]
Nov 19 16:50:01.50: [20798]: --> [2:OK]
Nov 19 16:50:01.50: [20798]: <-- [14:AT+FCLASS=2.0\r]
Nov 19 16:50:01.54: [20798]: --> [2:OK]
Nov 19 16:50:01.54: [20798]: <-- [9:AT+FLO=1\r]
Nov 19 16:50:01.58: [20798]: --> [2:OK]
Nov 19 16:50:01.58: [20798]: <-- [9:AT+FPP=0\r]
Nov 19 16:50:01.62: [20798]: --> [2:OK]
Nov 19 16:50:01.63: [20798]: <-- [9:AT+FBO=0\r]
Nov 19 16:50:01.66: [20798]: --> [2:OK]
Nov 19 16:50:01.66: [20798]: <-- [10:AT+FCT=30\r]
Nov 19 16:50:01.70: [20798]: --> [2:OK]
Nov 19 16:50:01.70: [20798]: <-- [15:AT+FNR=1,1,1,1\r]
Nov 19 16:50:01.74: [20798]: --> [2:OK]
Nov 19 16:50:01.74: [20798]: <-- [9:AT+FIE=0\r]
Nov 19 16:50:01.78: [20798]: --> [2:OK]
Nov 19 16:50:01.78: [20798]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Nov 19 16:50:01.83: [20798]: --> [2:OK]
Nov 19 16:50:01.83: [20798]: <-- [5:ATM0\r]
Nov 19 16:50:01.99: [20798]: --> [2:OK]
Nov 19 16:50:02.04: [20798]: <-- [14:AT+FCLASS=2.0\r]
Nov 19 16:50:02.18: [20798]: --> [2:OK]
Nov 19 16:50:02.18: [20798]: <-- [9:AT+FLO=1\r]
Nov 19 16:50:02.32: [20798]: --> [2:OK]
Nov 19 16:50:02.32: [20798]: <-- [9:AT+FPP=0\r]
Nov 19 16:50:02.46: [20798]: --> [2:OK]
Nov 19 16:50:02.46: [20798]: <-- [9:AT+FBO=0\r]
Nov 19 16:50:02.60: [20798]: --> [2:OK]
Nov 19 16:50:02.60: [20798]: <-- [10:AT+FCT=30\r]
Nov 19 16:50:02.74: [20798]: --> [2:OK]
Nov 19 16:50:02.74: [20798]: <-- [15:AT+FNR=1,1,1,1\r]
Nov 19 16:50:02.88: [20798]: --> [2:OK]
Nov 19 16:50:02.88: [20798]: <-- [9:AT+FIE=0\r]
Nov 19 16:50:03.03: [20798]: --> [2:OK]
Nov 19 16:50:03.03: [20798]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Nov 19 16:50:03.17: [20798]: --> [2:OK]
Nov 19 16:50:03.17: [20798]: <-- [22:AT+FLI="NothingSetup"\r]
Nov 19 16:50:03.32: [20798]: --> [2:OK]
Nov 19 16:50:03.33: [20798]: DIAL X#
Nov 19 16:50:03.33: [20798]: <-- [35:ATDTX#\r]
Nov 19 16:50:37.28: [20798]: --> [4:+FCO]
Nov 19 16:50:38.52: [20798]: --> [13:+FNF:BC530170]
Nov 19 16:50:38.52: [20798]: REMOTE NSF "BC530170"
Nov 19 16:50:39.25: [20798]: --> [27:+FCI:"      02 31 88 41 29"]
Nov 19 16:50:39.25: [20798]: REMOTE CSI "02 31 88 41 29"
Nov 19 16:50:39.54: [20798]: --> [20:+FIS:1,3,0,2,0,0,0,4]
Nov 19 16:51:11.33: [20798]: --> [7:+FHS:11]
Nov 19 16:51:11.33: [20798]: REMOTE HANGUP: No answer (T.30 T1 timeout) (code 
11)
Nov 19 16:51:11.34: [20798]: SEND FAILED: No answer (T.30 T1 timeout)
Nov 19 16:51:11.34: [20798]: SEND FAILED: No answer (T.30 T1 timeout); too 
many attempts to send
Nov 19 16:51:11.34: [20798]: <-- [5:ATH0\r]
Nov 19 16:51:11.34: [20798]: --> [2:OK]
Nov 19 16:51:11.36: [20798]: SESSION END

Then, after from dgautheron@magic.fr, I tried Class1 and the problem below 
disapears but a new one, "No response to MPS or EOP", appears for certain fax 
numbers :

Jan 05 19:41:34.16: [ 4266]: SESSION BEGIN 00006848 X
Jan 05 19:41:34.16: [ 4266]: SEND FAX: JOB 4416 DEST X# COMMID 00006848
Jan 05 19:41:34.17: [ 4266]: DELAY 2600 ms
Jan 05 19:41:36.76: [ 4266]: <-- [17:ATE0V1Q0X4S0=0H0\r]
Jan 05 19:41:37.07: [ 4266]: --> [2:OK]
Jan 05 19:41:37.07: [ 4266]: <-- [32:ATS8=2S7=60&H2&I2&R1S13=1&D2&C1\r]
Jan 05 19:41:37.24: [ 4266]: --> [2:OK]
Jan 05 19:41:37.24: [ 4266]: <-- [12:AT+FCLASS=1\r]
Jan 05 19:41:37.28: [ 4266]: --> [2:OK]
Jan 05 19:41:37.28: [ 4266]: <-- [9:AT+FAA=1\r]
Jan 05 19:41:37.32: [ 4266]: --> [2:OK]
Jan 05 19:41:37.32: [ 4266]: <-- [5:ATM0\r]
Jan 05 19:41:37.48: [ 4266]: --> [2:OK]
Jan 05 19:41:37.52: [ 4266]: <-- [12:AT+FCLASS=1\r]
Jan 05 19:41:37.66: [ 4266]: --> [2:OK]
Jan 05 19:41:37.67: [ 4266]: DIAL X#
Jan 05 19:41:37.67: [ 4266]: <-- [35:ATDTX#\r]
Jan 05 19:42:05.61: [ 4266]: --> [7:CONNECT]
Jan 05 19:42:05.61: [ 4266]: --> [2:OK]
Jan 05 19:42:05.61: [ 4266]: <-- [9:AT+FRH=3\r]
Jan 05 19:42:05.65: [ 4266]: --> [7:CONNECT]
Jan 05 19:42:05.78: [ 4266]: --> [2:OK]
Jan 05 19:42:05.78: [ 4266]: REMOTE best rate 9600 bit/s
Jan 05 19:42:05.78: [ 4266]: REMOTE max page width 1728 pixels in 215 mm
Jan 05 19:42:05.78: [ 4266]: REMOTE max A4 page length (297 mm)
Jan 05 19:42:05.78: [ 4266]: REMOTE best vres 7.7 line/mm
Jan 05 19:42:05.78: [ 4266]: REMOTE best format 1-D MR
Jan 05 19:42:05.78: [ 4266]: REMOTE best 20 ms/scanline
Jan 05 19:42:05.78: [ 4266]: USE 9600 bit/s
Jan 05 19:42:05.78: [ 4266]: USE 20 ms/scanline
Jan 05 19:42:05.78: [ 4266]: SEND file "docq/doc4448.ps;01"
Jan 05 19:42:05.79: [ 4266]: USE page width 1728 pixels in 215 mm
Jan 05 19:42:05.79: [ 4266]: USE A4 page length (297 mm)
Jan 05 19:42:05.79: [ 4266]: USE 7.7 line/mm
Jan 05 19:42:05.79: [ 4266]: USE 1-D MR
Jan 05 19:42:05.79: [ 4266]: SEND training at v.29 9600 bit/s
Jan 05 19:42:05.79: [ 4266]: <-- [9:AT+FTH=3\r]
Jan 05 19:42:05.90: [ 4266]: --> [7:CONNECT]
Jan 05 19:42:07.64: [ 4266]: --> [7:CONNECT]
Jan 05 19:42:08.34: [ 4266]: --> [2:OK]
Jan 05 19:42:08.34: [ 4266]: DELAY 75 ms
Jan 05 19:42:08.40: [ 4266]: <-- [10:AT+FTM=96\r]
Jan 05 19:42:08.72: [ 4266]: --> [7:CONNECT]
Jan 05 19:42:10.24: [ 4266]: --> [2:OK]
Jan 05 19:42:10.24: [ 4266]: <-- [9:AT+FRH=3\r]
Jan 05 19:42:11.77: [ 4266]: --> [7:CONNECT]
Jan 05 19:42:11.90: [ 4266]: --> [2:OK]
Jan 05 19:42:11.90: [ 4266]: TRAINING succeeded
Jan 05 19:42:11.91: [ 4266]: <-- [10:AT+FTM=96\r]
Jan 05 19:42:12.21: [ 4266]: --> [7:CONNECT]
Jan 05 19:42:12.21: [ 4266]: SEND begin page
Jan 05 19:42:55.51: [ 4266]: SENT 55016 bytes of data
Jan 05 19:43:05.24: [ 4266]: SENT 11016 bytes of data
Jan 05 19:43:05.24: [ 4266]: SEND 1D RTC
Jan 05 19:43:05.24: [ 4266]: SEND end page
Jan 05 19:43:07.34: [ 4266]: --> [2:OK]
Jan 05 19:43:07.34: [ 4266]: DELAY 95 ms
Jan 05 19:43:07.43: [ 4266]: SEND send EOP (no more pages or documents)
Jan 05 19:43:07.43: [ 4266]: <-- [9:AT+FTH=3\r]
Jan 05 19:43:07.55: [ 4266]: --> [7:CONNECT]
Jan 05 19:43:08.76: [ 4266]: --> [2:OK]
Jan 05 19:43:08.76: [ 4266]: <-- [9:AT+FRH=3\r]
Jan 05 19:43:11.80: [ 4266]: --> [7:CONNECT]
Jan 05 19:43:12.05: [ 4266]: MODEM <Timeout>
Jan 05 19:43:12.05: [ 4266]: SEND send EOP (no more pages or documents)
Jan 05 19:43:12.05: [ 4266]: <-- [9:AT+FTH=3\r]

I was wondering which Class to use and how to solve one or the other problem ?

Thanks a lot in advance for your help.			Gildas.
-- 
Gildas PERROT, perrot@francenet.fr         __o
FranceNet, 28 rue Desaix, 75015 Paris ---_ \<,_
http://www.francenet.fr            ---- (_)/ (_)