HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: HELP: Document was encoded with 2DMR, but client does not support , this data format




...addon:

the info file for the destination reports:

supportsHighRes:yes
supports2DEncoding:no
supportsPostScript:no
calledBefore:yes
maxPageWidth:1728
maxPageLength:-1
maxSignallingRate:"9600"
minScanlineTime:"20ms/10ms"
remoteCSI:""
sendFailures:6
lastSendFailure:"Document was encoded with 2DMR, but client does not support this data format"
dialFailures:0
lastDialFailure:"No answer (T.30 T1 timeout)"


the sendfax parameters were:

sendfax  -h ttyS1@gw -n -R -i P0000408 -k 'now +4 hours' -d xxxxx 


thanx for ANY help is very much appreciated!

fred.


On Wed, 21 May 1997, Fred Meyer wrote:

> Hi folks,
> 
> ...im using HylaFAX v4.0pl1 build from source on Linux with GS-4.03
> and a MultiTech MT2834ZDXI modem.
> 
> ...i'm generating about 350 faxes a day with this setup.
> I just came up with the following error:
> 
>  "Document was encoded with 2DMR, but client does not support this data
> format"
> 
> ????? All faxes are generated with the SAME list of parameters via
> sendfax....the parameter that selects 1-D or 2-D encoding is NOT used!!
> All documents are submitted in PS format.
> All other remote sites, that appear to have the same remote capabilities
> like the one below, are correctly fed with a 1-D document.
> 
> WHAT happend? ...help!
> 
> TIA,
>    fred
> 
> ---session log:
> May 21 11:21:49.70: [14730]: SESSION BEGIN 00000685 27113913300
> May 21 11:21:49.70: [14730]: SEND FAX: JOB 436 DEST 391-3300 COMMID 00000685
> May 21 11:21:49.70: [14730]: DELAY 2600 ms
> May 21 11:21:52.30: [14730]: <-- [15:ATE0V1Q0S0=0H0\r]
> May 21 11:21:52.51: [14730]: --> [14:ATE0V1Q0S0=0H0]
> May 21 11:21:52.51: [14730]: --> [2:OK]
> May 21 11:21:52.51: [14730]: <-- [21:ATS8=2S7=60&E4&D3&C1\r]
> May 21 11:21:52.68: [14730]: --> [2:OK]
> May 21 11:21:52.68: [14730]: <-- [12:AT+FCLASS=2\r]
> May 21 11:21:52.84: [14730]: --> [2:OK]
> May 21 11:21:52.84: [14730]: <-- [10:AT+FTBC=0\r]
> May 21 11:21:53.00: [14730]: --> [2:OK]
> May 21 11:21:53.00: [14730]: <-- [10:AT+FBOR=0\r]
> May 21 11:21:53.16: [14730]: --> [2:OK]
> May 21 11:21:53.16: [14730]: <-- [13:AT+FPHCTO=30\r]
> May 21 11:21:53.32: [14730]: --> [2:OK]
> May 21 11:21:53.32: [14730]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
> May 21 11:21:53.49: [14730]: --> [2:OK]
> May 21 11:21:53.49: [14730]: <-- [5:ATM0\r]
> May 21 11:21:53.65: [14730]: --> [2:OK]
> May 21 11:21:53.65: [14730]: <-- [12:AT+FCLASS=2\r]
> May 21 11:21:53.92: [14730]: --> [2:OK]
> May 21 11:21:53.92: [14730]: <-- [10:AT+FTBC=0\r]
> May 21 11:21:54.18: [14730]: --> [2:OK]
> May 21 11:21:54.18: [14730]: <-- [10:AT+FBOR=0\r]
> May 21 11:21:54.44: [14730]: --> [2:OK]
> May 21 11:21:54.44: [14730]: <-- [13:AT+FPHCTO=30\r]
> May 21 11:21:54.70: [14730]: --> [2:OK]
> May 21 11:21:54.70: [14730]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
> May 21 11:21:54.97: [14730]: --> [2:OK]
> May 21 11:21:54.97: [14730]: <-- [31:AT+FLID="Mediswitch (Pty) Ltd"\r]
> May 21 11:21:55.24: [14730]: --> [2:OK]
> May 21 11:21:55.24: [14730]: DIAL xxxxx
> May 21 11:21:55.24: [14730]: <-- [13:ATDTxxxxx@\r]
> May 21 11:22:38.49: [14730]: --> [5:+FCON]
> May 21 11:22:41.60: [14730]: --> [105:+FNSF:00 00 31 00 4E B8 00 86 0D DD 00 00 DD DD 00 00 DD DD DD DD DD 97 05 21 03 11 02 54 ED 23 10 00 00 ]
> May 21 11:22:41.60: [14730]: REMOTE NSF "00 00 31 00 4E B8 00 86 0D DD 00 00 DD DD 00 00 DD DD DD DD DD 97 05 21 03 11 02 54 ED 23 10 00 00"
> May 21 11:22:41.72: [14730]: --> [28:+FCSI:"                    "]
> May 21 11:22:41.72: [14730]: REMOTE CSI ""
> May 21 11:22:41.72: [14730]: --> [21:+FDIS:1,3,0,2,0,0,0,4]
> May 21 11:22:41.72: [14730]: --> [2:OK]
> May 21 11:22:41.72: [14730]: REMOTE best rate 9600 bit/s
> May 21 11:22:41.72: [14730]: REMOTE max page width 1728 pixels in 215 mm
> May 21 11:22:41.72: [14730]: REMOTE max unlimited page length 
> May 21 11:22:41.72: [14730]: REMOTE best vres 7.7 line/mm
> May 21 11:22:41.72: [14730]: REMOTE best format 1-D MR
> May 21 11:22:41.72: [14730]: REMOTE best 20 ms, 10 ms/scanline
> May 21 11:22:41.72: [14730]: USE 9600 bit/s
> May 21 11:22:41.72: [14730]: USE 20 ms, 10 ms/scanline
> May 21 11:22:41.72: [14730]: SEND file "docq/doc436.ps;40"
> May 21 11:22:41.92: [14730]: Document was encoded with 2DMR, but client does not support this data format
> May 21 11:22:41.92: [14730]: <-- [5:ATH0\r]
> May 21 11:22:43.55: [14730]: --> [7:+FHNG:2]
> May 21 11:22:43.55: [14730]: REMOTE HANGUP: Call aborted,  from +FK or <CAN> (code 2)
> May 21 11:22:44.19: [14730]: --> [2:OK]
> May 21 11:22:44.19: [14730]: SESSION END
> 
> 




Project hosted by iFAX Solutions