HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: squished faxes when receiving a fax



> >  Date: Sun, 11 May 1997 01:49:50 -0400 (EDT)
> >  From: High Mercury <merc@icanect.net>
> >  I am using a multitech2834MR modem to receive faxes and when I receive
> >  a fax using 4.0pl1, they only take up half the page. Here is the log of the
> >  reception:
> 
> Sounds like a flow control problem - try changing from whatever you're
> using to the to the other method (i.e., if you're using RTSCTS, try XONXOFF).

I tried switching it to xonxoff but received the same fax squished into
1/2 a page: 

---------------------------------------------------------------------------
May 13 21:12:20.23: [ 6281]: SESSION BEGIN 00003299 1xxxxxxxxx
May 13 21:12:20.24: [ 6281]: <-- [4:ATA\r]
May 13 21:12:27.40: [ 6281]: --> [74:+FHT:FF 03 40 37 30 38 30 30 32 36 35 30 33
 20 20 20 20 20 20 20 20 20 20 ]
May 13 21:12:28.19: [ 6281]: --> [26:+FHT:FF 13 80 00 6E FA 00 ]
May 13 21:12:28.96: [ 6281]: --> [5:+FCON]
May 13 21:12:28.96: [ 6281]: STATE CHANGE: ANSWERING -> RECEIVING
May 13 21:12:28.96: [ 6281]: MODEM input buffering enabled
May 13 21:12:28.97: [ 6281]: RECV FAX: begin
May 13 21:12:30.64: [ 6281]: --> [74:+FHR:FF 03 43 37 32 32 32 31 32 36 35 30 33
 20 20 20 20 20 20 20 20 20 20 ]
May 13 21:12:30.90: [ 6281]: --> [26:+FHR:FF 13 83 00 22 98 00 ]
May 13 21:12:34.18: [ 6281]: --> [28:+FTSI:"          xxxxxxxxxx"]
May 13 21:12:34.18: [ 6281]: REMOTE TSI "xxxxxxxxxx"
May 13 21:12:34.18: [ 6281]: --> [21:+FDCS:0,5,0,2,0,0,0,1]
May 13 21:12:34.18: [ 6281]: REMOTE wants 14400 bit/s
May 13 21:12:34.18: [ 6281]: REMOTE wants page width 1728 pixels in 215 mm
May 13 21:12:34.18: [ 6281]: REMOTE wants unlimited page length 
May 13 21:12:34.18: [ 6281]: REMOTE wants 3.85 line/mm
May 13 21:12:34.18: [ 6281]: REMOTE wants 1-D MR
May 13 21:12:34.18: [ 6281]: --> [2:OK]
May 13 21:12:34.18: [ 6281]: <-- [7:AT+FDR\r]
May 13 21:12:35.28: [ 6281]: --> [14:+FHT:FF 13 84 ]
May 13 21:12:35.57: [ 6281]: --> [5:+FCFR]
May 13 21:12:35.57: [ 6281]: --> [28:+FTSI:"          xxxxxxxxxx"]
May 13 21:12:35.57: [ 6281]: REMOTE TSI "xxxxxxxxxx"
May 13 21:12:35.57: [ 6281]: --> [21:+FDCS:0,5,0,2,0,0,0,1]
May 13 21:12:35.57: [ 6281]: REMOTE wants 14400 bit/s
May 13 21:12:35.57: [ 6281]: REMOTE wants page width 1728 pixels in 215 mm
May 13 21:12:35.57: [ 6281]: REMOTE wants unlimited page length 
May 13 21:12:35.57: [ 6281]: REMOTE wants 3.85 line/mm
May 13 21:12:35.57: [ 6281]: REMOTE wants 1-D MR
May 13 21:12:36.31: [ 6281]: --> [7:CONNECT]
May 13 21:12:36.31: [ 6281]: RECV: begin page
May 13 21:12:36.31: [ 6281]: MODEM set XON/XOFF/FLUSH: input ignored, output generated
May 13 21:12:36.31: [ 6281]: RECV: send trigger 022
May 13 21:12:36.31: [ 6281]: <-- data [1]
May 13 21:12:52.70: [ 6281]: RECV: 29242 bytes of data, 1056 total lines
May 13 21:12:52.70: [ 6281]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled
May 13 21:12:52.70: [ 6281]: --> [18:+FPTS:1,1056,0,0,0]
May 13 21:12:53.91: [ 6281]: --> [14:+FHR:FF 13 2F ]
May 13 21:12:53.91: [ 6281]: --> [6:+FET:2]
May 13 21:12:53.91: [ 6281]: RECV recv EOP (no more pages or documents)
May 13 21:12:53.91: [ 6281]: --> [2:OK]
May 13 21:12:53.91: [ 6281]: RECV send MCF (message confirmation)
May 13 21:12:53.92: [ 6281]: <-- [7:AT+FDR\r]
May 13 21:12:55.08: [ 6281]: --> [14:+FHT:FF 13 8C ]
May 13 21:12:56.06: [ 6281]: RECV FAX: end
May 13 21:12:56.07: [ 6281]: SESSION END
---------------------------------------------------------------------------

Like I said before, this only happens when the fax machine is sending a
fax to the multitech modem in standard mode.  The weird thing though, is that
I can send a standard fax from the modem to the fax machine I'm using to
test and it takes up the whole page and is not squished.

Any other ideas??

thanks

merc




Project hosted by iFAX Solutions