![]() |
Is there a patch for hardware flow control on Solaris 2.4 on a Sparc5 using /dev/cua/b ? I searched all over at SUN and could not find a patch to fix this. I could not get the Modem to respond until I set flow control to xonxoff but know I get receive errors in phase C everytime. I have tried different baud rates 38400, 19200 and 9600. Solaris package installed hylafax-sparc-sunos5.5-v4.0pl1-pkg Solaris 2.4 on Sparc 5 using /dev/cua/b Modem MuliTech MT2834ZDX/0314C Thanks John Ratcliffe UCSD SOE. ------ recieve fax log file ---------- Apr 01 12:41:57.74: [ 6476]: SESSION BEGIN 00000004 16195340408 Apr 01 12:41:57.75: [ 6476]: <-- [4:ATA\r] Apr 01 12:42:05.73: [ 6476]: --> [5:+FCON] Apr 01 12:42:05.74: [ 6476]: ANSWER: FAX CONNECTION Apr 01 12:42:05.76: [ 6476]: RECV FAX: begin Apr 01 12:42:12.87: [ 6476]: --> [28:+FTSI:" 619 534 3087"] Apr 01 12:42:12.88: [ 6476]: REMOTE TSI "619 534 3087" Apr 01 12:42:12.88: [ 6476]: --> [21:+FDCS:0,3,0,2,1,0,0,0] Apr 01 12:42:12.88: [ 6476]: REMOTE wants 9600 bit/s Apr 01 12:42:12.88: [ 6476]: REMOTE wants page width 1728 pixels in 215 mm Apr 01 12:42:12.88: [ 6476]: REMOTE wants unlimited page length Apr 01 12:42:12.89: [ 6476]: REMOTE wants 3.85 line/mm Apr 01 12:42:12.89: [ 6476]: REMOTE wants 2-D MR Apr 01 12:42:12.89: [ 6476]: --> [2:OK] Apr 01 12:42:12.89: [ 6476]: <-- [7:AT+FDR\r] Apr 01 12:45:12.89: [ 6476]: REMOTE HANGUP: Unspecified Phase C error, including too much delay between TCF and +FDR command (code 90) Apr 01 12:45:12.89: [ 6476]: RECV FAX (00000004): recvq/fax00004.tif from 619 53 4 3087, route to <unspecified>, 0 pages in 3:07 Apr 01 12:45:13.03: [ 6476]: RECV FAX: Unspecified Phase C error, including too much delay between TCF and +FDR command Apr 01 12:45:13.07: [ 6476]: <-- [6:AT+FK\r] Apr 01 12:45:14.63: [ 6476]: --> [7:+FHNG:2] Apr 01 12:45:14.63: [ 6476]: REMOTE HANGUP: Call aborted, from +FK or <CAN> (co de 2) Apr 01 12:45:15.28: [ 6476]: --> [2:OK] Apr 01 12:45:15.35: [ 6476]: RECV FAX (00000004): session with 619 534 3087 term inated abnormally: Unspecified Phase C error, including too much delay between T CF and +FDR command Apr 01 12:45:15.35: [ 6476]: RECV FAX: bin/faxrcvd "recvq/fax00004.tif" "cua_b" "00000004" "Unspecified Phase C error, including too much delay between TCF and +FDR command" Apr 01 12:45:18.22: [ 6476]: RECV FAX: end Apr 01 12:45:18.22: [ 6476]: SESSION END