Re: {HELP} I cannot receive correct fax

[gyqian@iss.nus.sg (Qian Guo Yu)]

----------
X-Sun-Data-Type: text
X-Sun-Data-Description: text
X-Sun-Data-Name: text
X-Sun-Charset: us-ascii
X-Sun-Content-Lines: 41


> 
> Qian Guo Yu wrote:
>     
>     I can't find my server trace. Attached is a session log and
> 
> the server trace is written by syslogd(1M) according the rules
> in /etc/syslog.conf;
> 

The file '/etc/syslog.conf' only has one line:
local0.notice               /var/adm/syslog

And, the file 'var/adm/syslog' has two lines:
Jan 27 16:58:1 prsmpc4 syslogd: restart
Jan 21 10:02:36 prsmpc4 syslog: accept: SIOCGPGRP failed errno 22

> 
> Your modem was told to dial "ATD9T7744998" if this is a correct
> dial string check-out the destination (e.g. try dial from
> another phone to dial the same number); if this is not the
> correct dial string check the ModemDialCmd in the modem
> config-file;
>
> 	....
>     
>     # NB: If you need to prefix phone numbers to get through a PBX,
>     #     put it in the ModemDialCmd; e.g. "DT9%s@".
>     ModemDialCmd:           ATD9T%s         # no '@' 'cuz then busy not recognized
> 
> 	matthias

I corrected the ModemDialCmd to "ATDT9%s" in the modem config file 
and got the same result: the receiver only got some of the contents.
(it looks like half page, and some lines are merged together). 

I attached a new log file which shows the successful sending. I hope it
is helpful to find the problem.

Thank you again.
Qian Guo Yu
----------
X-Sun-Data-Type: default
X-Sun-Data-Description: default
X-Sun-Data-Name: c00000062
X-Sun-Charset: us-ascii
X-Sun-Content-Lines: 116

Mar 19 10:03:45.25: [ 3902]: SESSION BEGIN 00000062 657744998
Mar 19 10:03:45.26: [ 3902]: SEND FAX: JOB 41 DEST 7744998 COMMID 00000062
Mar 19 10:03:45.30: [ 3902]: DELAY 2600 ms
Mar 19 10:03:47.90: [ 3902]: <-- [39:AT&B1&N0&S0*F0S18=4S38.3=1E0V1Q0S0=0H0\r]
Mar 19 10:03:48.10: [ 3902]: --> [2:OK]
Mar 19 10:03:48.10: [ 3902]: <-- [21:ATS8=2S7=60&H3&D2&C1\r]
Mar 19 10:03:48.14: [ 3902]: --> [2:OK]
Mar 19 10:03:48.14: [ 3902]: <-- [14:AT+FCLASS=2.0\r]
Mar 19 10:03:48.18: [ 3902]: --> [2:OK]
Mar 19 10:03:48.18: [ 3902]: <-- [9:AT+FLO=2\r]
Mar 19 10:03:48.22: [ 3902]: --> [2:OK]
Mar 19 10:03:48.22: [ 3902]: <-- [9:AT+FPP=0\r]
Mar 19 10:03:48.26: [ 3902]: --> [2:OK]
Mar 19 10:03:48.26: [ 3902]: <-- [9:AT+FBO=0\r]
Mar 19 10:03:48.30: [ 3902]: --> [2:OK]
Mar 19 10:03:48.30: [ 3902]: <-- [10:AT+FCT=30\r]
Mar 19 10:03:48.34: [ 3902]: --> [2:OK]
Mar 19 10:03:48.34: [ 3902]: <-- [15:AT+FNR=1,1,1,1\r]
Mar 19 10:03:48.38: [ 3902]: --> [2:OK]
Mar 19 10:03:48.38: [ 3902]: <-- [9:AT+FIE=0\r]
Mar 19 10:03:48.42: [ 3902]: --> [2:OK]
Mar 19 10:03:48.42: [ 3902]: <-- [23:AT+FCC=1,5,2,2,1,0,0,0\r]
Mar 19 10:03:48.46: [ 3902]: --> [2:OK]
Mar 19 10:03:48.46: [ 3902]: <-- [5:ATM0\r]
Mar 19 10:03:48.50: [ 3902]: --> [2:OK]
Mar 19 10:03:48.50: [ 3902]: Unable to set RT scheduling parameters: Invalid argument
Mar 19 10:03:48.52: [ 3902]: <-- [14:AT+FCLASS=2.0\r]
Mar 19 10:03:48.66: [ 3902]: --> [2:OK]
Mar 19 10:03:48.66: [ 3902]: <-- [9:AT+FLO=2\r]
Mar 19 10:03:48.80: [ 3902]: --> [2:OK]
Mar 19 10:03:48.80: [ 3902]: <-- [9:AT+FPP=0\r]
Mar 19 10:03:48.94: [ 3902]: --> [2:OK]
Mar 19 10:03:48.94: [ 3902]: <-- [9:AT+FBO=0\r]
Mar 19 10:03:49.08: [ 3902]: --> [2:OK]
Mar 19 10:03:49.08: [ 3902]: <-- [10:AT+FCT=30\r]
Mar 19 10:03:49.22: [ 3902]: --> [2:OK]
Mar 19 10:03:49.22: [ 3902]: <-- [15:AT+FNR=1,1,1,1\r]
Mar 19 10:03:49.36: [ 3902]: --> [2:OK]
Mar 19 10:03:49.36: [ 3902]: <-- [9:AT+FIE=0\r]
Mar 19 10:03:49.50: [ 3902]: --> [2:OK]
Mar 19 10:03:49.50: [ 3902]: <-- [23:AT+FCC=1,5,2,2,1,0,0,0\r]
Mar 19 10:03:49.64: [ 3902]: --> [2:OK]
Mar 19 10:03:49.64: [ 3902]: <-- [22:AT+FLI="+65-771-5230"\r]
Mar 19 10:03:49.78: [ 3902]: --> [2:OK]
Mar 19 10:03:49.78: [ 3902]: DIAL 7744998
Mar 19 10:03:49.78: [ 3902]: <-- [13:ATDT97744998\r]
Mar 19 10:04:10.86: [ 3902]: --> [4:+FCO]
Mar 19 10:04:10.86: [ 3902]: --> [18:+FNF:BC 53 01 60  ]
Mar 19 10:04:10.86: [ 3902]: REMOTE NSF "BC 53 01 60"
Mar 19 10:04:10.86: [ 3902]: --> [26:+FCI:             7744998 ]
Mar 19 10:04:10.86: [ 3902]: REMOTE CSI "7744998"
Mar 19 10:04:10.86: [ 3902]: --> [20:+FIS:1,3,0,2,1,0,0,0]
Mar 19 10:04:10.86: [ 3902]: --> [2:OK]
Mar 19 10:04:10.86: [ 3902]: REMOTE best rate 9600 bit/s
Mar 19 10:04:10.86: [ 3902]: REMOTE max page width 1728 pixels in 215 mm
Mar 19 10:04:10.86: [ 3902]: REMOTE max unlimited page length 
Mar 19 10:04:10.86: [ 3902]: REMOTE best vres 7.7 line/mm
Mar 19 10:04:10.86: [ 3902]: REMOTE best format 2-D MR
Mar 19 10:04:10.86: [ 3902]: REMOTE best 0 ms/scanline
Mar 19 10:04:10.86: [ 3902]: USE 9600 bit/s
Mar 19 10:04:10.86: [ 3902]: USE 0 ms/scanline
Mar 19 10:04:10.86: [ 3902]: SEND file "docq/doc73.ps;41"
Mar 19 10:04:10.86: [ 3902]: USE page width 1728 pixels in 215 mm
Mar 19 10:04:10.86: [ 3902]: USE unlimited page length 
Mar 19 10:04:10.86: [ 3902]: USE 7.7 line/mm
Mar 19 10:04:10.86: [ 3902]: USE 2-D MR
Mar 19 10:04:10.86: [ 3902]: <-- [23:AT+FIS=1,3,0,2,1,0,0,0\r]
Mar 19 10:04:11.00: [ 3902]: --> [2:OK]
Mar 19 10:04:11.00: [ 3902]: <-- [7:AT+FDT\r]
Mar 19 10:04:16.70: [ 3902]: --> [20:+FCS:1,3,0,2,1,0,0,0]
Mar 19 10:04:17.24: [ 3902]: --> [7:CONNECT]
Mar 19 10:04:17.24: [ 3902]: SEND begin page
Mar 19 10:04:17.24: [ 3902]: <-- data [1027]
Mar 19 10:04:17.24: [ 3902]: <-- data [1030]
Mar 19 10:04:17.24: [ 3902]: <-- data [1026]
Mar 19 10:04:17.46: [ 3902]: <-- data [1030]
Mar 19 10:04:17.72: [ 3902]: <-- data [1028]
Mar 19 10:04:17.98: [ 3902]: <-- data [1029]
Mar 19 10:04:18.26: [ 3902]: <-- data [1029]
Mar 19 10:04:18.52: [ 3902]: <-- data [1028]
Mar 19 10:04:18.78: [ 3902]: <-- data [1027]
Mar 19 10:04:19.06: [ 3902]: <-- data [1029]
Mar 19 10:04:19.32: [ 3902]: <-- data [1032]
Mar 19 10:04:19.60: [ 3902]: <-- data [1028]
Mar 19 10:04:19.86: [ 3902]: <-- data [1028]
Mar 19 10:04:20.12: [ 3902]: <-- data [1027]
Mar 19 10:04:20.40: [ 3902]: <-- data [1031]
Mar 19 10:04:20.66: [ 3902]: <-- data [1030]
Mar 19 10:04:20.92: [ 3902]: <-- data [1035]
Mar 19 10:04:21.20: [ 3902]: <-- data [1032]
Mar 19 10:04:21.46: [ 3902]: <-- data [1032]
Mar 19 10:04:21.72: [ 3902]: <-- data [1031]
Mar 19 10:04:22.00: [ 3902]: <-- data [1029]
Mar 19 10:04:22.26: [ 3902]: <-- data [1031]
Mar 19 10:04:22.52: [ 3902]: <-- data [1037]
Mar 19 10:04:22.80: [ 3902]: <-- data [1028]
Mar 19 10:04:23.06: [ 3902]: <-- data [1029]
Mar 19 10:04:23.34: [ 3902]: <-- data [1027]
Mar 19 10:04:23.60: [ 3902]: <-- data [1032]
Mar 19 10:04:23.86: [ 3902]: <-- data [1034]
Mar 19 10:04:24.14: [ 3902]: <-- data [1030]
Mar 19 10:04:24.40: [ 3902]: <-- data [582]
Mar 19 10:04:24.68: [ 3902]: SENT 30272 bytes of data
Mar 19 10:04:24.68: [ 3902]: SEND 2D RTC
Mar 19 10:04:24.68: [ 3902]: <-- data [10]
Mar 19 10:04:24.94: [ 3902]: SEND end page
Mar 19 10:04:24.94: [ 3902]: SEND send EOP (no more pages or documents)
Mar 19 10:04:24.94: [ 3902]: <-- data [2]
Mar 19 10:04:47.04: [ 3902]: --> [7:+FHS:00]
Mar 19 10:04:47.04: [ 3902]: REMOTE HANGUP: Normal and proper end of connection (code 0)
Mar 19 10:04:47.04: [ 3902]: SEND recv MCF (message confirmation)
Mar 19 10:04:47.06: [ 3902]: SEND FAX (00000062): FROM gyqian@prsmpc4 TO 7744998 (page 1 of 1 sent in 0:37)
Mar 19 10:04:47.06: [ 3902]: SEND FAX (00000062): FROM gyqian@prsmpc4 TO 7744998 (docq/doc73.ps;41 sent in 0:37)
Mar 19 10:04:47.10: [ 3902]: <-- [5:ATH0\r]
Mar 19 10:04:47.10: [ 3902]: --> [2:OK]
Mar 19 10:04:47.10: [ 3902]: SESSION END