pager nro 382 para 6223315 failed

[Fax Account <fax@buriti.com.br>]

Seu pager para 6223315 falhou por que :
    Job has no PIN to send to

    ---- Transcript of session follows ----

Feb 05 09:50:13.39: [29925]: SESSION BEGIN 00000813 55926223315
Feb 05 09:50:13.39: [29925]: SEND PAGE: JOB 382 DEST 6223315 COMMID 00000813
Feb 05 09:50:13.39: [29925]: MODEM set DTR OFF
Feb 05 09:50:13.39: [29925]: DELAY 2600 ms
Feb 05 09:50:16.00: [29925]: MODEM set DTR ON
Feb 05 09:50:16.00: [29925]: MODEM set baud rate: 38400 baud, input flow RTS/CTS, output flow RTS/CTS
Feb 05 09:50:16.00: [29925]: MODEM flush i/o
Feb 05 09:50:16.00: [29925]: <-- [17:ATE0V1Q0X4S0=0H0\r]
Feb 05 09:50:16.17: [29925]: --> [16:ATE0V1Q0X4S0=0H0]
Feb 05 09:50:16.17: [29925]: --> [2:OK]
Feb 05 09:50:16.17: [29925]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=1&D2&C1\r]
Feb 05 09:50:16.34: [29925]: --> [2:OK]
Feb 05 09:50:16.34: [29925]: <-- [5:ATM1\r]
Feb 05 09:50:16.51: [29925]: --> [2:OK]
Feb 05 09:50:16.51: [29925]: MODEM set parity: 8 bits, no parity
Feb 05 09:50:16.51: [29925]: MODEM input buffering enabled
Feb 05 09:50:16.51: [29925]: <-- [12:AT+FCLASS=0\r]
Feb 05 09:50:16.67: [29925]: --> [2:OK]
Feb 05 09:50:16.67: [29925]: <-- [15:AT&A0&K0&M0&N2\r]
Feb 05 09:50:16.94: [29925]: --> [2:OK]
Feb 05 09:50:16.94: [29925]: DIAL 6223315
Feb 05 09:50:16.94: [29925]: <-- [12:ATDT6223315\r]
Feb 05 09:50:34.24: [29925]: --> [12:CONNECT 1200]
Feb 05 09:50:34.24: [29925]: EXPECT ID (paging central identification)
Feb 05 09:50:35.24: [29925]: MODEM TIMEOUT: reading line from modem
Feb 05 09:50:35.24: [29925]: RECV ID ("ID=")
Feb 05 09:50:35.24: [29925]: SEND device identification/login request
Feb 05 09:50:35.70: [29925]: RECV ACK (login successful)
Feb 05 09:50:35.70: [29925]: RECV go-ahead (prologue done)
Feb 05 09:50:35.70: [29925]: SEND message block
Feb 05 09:50:36.72: [29925]: RECV ACK (message block accepted)
Feb 05 09:50:36.72: [29925]: RECV: * acknowledgement *
Feb 05 09:50:56.70: [29925]: RECV: +++^W^SQ^ֻN�^S^�rf�w�iUUUUUUUUUUUUUUUUUUUUUUU
Feb 05 09:50:56.70: [29925]: RECV: NO CARRIER
Feb 05 09:51:26.70: [29925]: MODEM TIMEOUT: reading line from modem
Feb 05 09:51:26.70: [29925]: <-- [5:ATH0\r]
Feb 05 09:51:26.97: [29925]: --> [2:OK]
Feb 05 09:51:26.97: [29925]: MODEM input buffering enabled
Feb 05 09:51:26.97: [29925]: MODEM set DTR OFF
Feb 05 09:51:26.97: [29925]: SESSION END

    ---- Fax nao enviado ----

      Destinatario: 6223315
             JobID: 382
           GroupID: 382
         Remetente: Mario de Mello Bittencourt Neto
            E-mail: mneto@zeus.buriti.com.br
            CommID: 00000813
Submetido a partir: localhost
            Status: Job has no PIN to send to
           Dialogs: 1 (exchanges with remote device)
        Tentativas: 0 (ligacoes consecutivas falhas ao destinatario)
          Ligacoes: 1 (total de ligacoes efetuadas)

    ---- Messagem ----

LELE 1


Well I have used sendpage -D -p teste "LELE 1", where teste is an  entry
in my pagermap

^GB([0-9]+)$	6223315/\1 
^teste$		6223315/2578
.*		reject

BUT, this is not the only strange behavour. I have decided to send 10
pages simultaneosly (sp?) with sendpage -D -p teste "LELE 1" , sendpage -D
-p teste "LELE 2", and so on.
The first two were sent and I received email with "your pager to 6223315
failed because :
    Job has no PIN to send to

And after this the other 8 jobs finished at the same time with 
"Your pager to 6223315 could not be completed before the appointed
deadline."

    ---- pager not sent ----

      Destinatario: 6223315
             JobID: 385
           GroupID: 385
         Remetente: Mario de Mello Bittencourt Neto
            E-mail: mneto@zeus.buriti.com.br
Submetido a partir: localhost
            Status: Blocked by concurrent jobs
           Dialogs: 0 (exchanges with remote device)
        Tentativas: 0 (ligacoes consecutivas falhas ao destinatario)
          Ligacoes: 0 (total de ligacoes efetuadas)

Questions : 
- What I am doing wrong ? Where can I set this deadline and why
are all jobs finishing like that ?

- Regarding that "JOB has no PIN to send to". I noticed some lines and I'd
like to know if they are correct 
Feb 05 09:50:35.70: [29925]: SEND message block
Feb 05 09:50:36.72: [29925]: RECV ACK (message block accepted)
Feb 05 09:50:36.72: [29925]: RECV: * acknowledgement *
Feb 05 09:50:56.70: [29925]: RECV:+++^W^SQ^N^S^rfwiUUUUUUUUUUUUUUUUUUUUUUU

 * * * *  Is the line above garbage ? Wrong Parity setting ? * * * *

Feb 05 09:50:56.70: [29925]: RECV: NO CARRIER

The company set parity none, stopbits 1 and word length 8. My config.modem
PagerSetupCmds:         AT&A0&K0&M0&N2
PagerTTYParity:         none
IXOIDProbe:             1
IXOIDTimeout:           10
IXOLoginRetries:        3

Sorry for the long append.

thanks.

+---------------------------------------------------------------------+
| Mario de Mello Bittencourt Neto                System Administrator |
| WebSlave !                                   Argo Internet Provider |
+---------------------------------------------------------------------+
| Key fingerprint = CB B8 0E 90 EE 9C D1 91  B5 5E B1 EC 83 4D 78 9B  |
+---------------------------------------------------------------------+