Receiving works --- almost

[Stefan Pettersson <spp@lysator.liu.se>]

-----BEGIN PGP SIGNED MESSAGE-----

When I receive a fax from most fax machines I get the page ok and my modem
disconnects. But the sending fax machine indicates "Tx error".
If I lift the phone and listen (in my end) I hear the fax machine still trying
to talk.

Sending fax works perfectly.


OS: Linux 2.0.27 (Slackware)
The Software: v4.0pl1 (binary dist)
Modem: Microcom DeskPorte 33.6S class 2
Chip: MODEM ROCKWELL AC/V34/V1.510-V34_DS


Jan 24 12:34:04.95: [  341]: SESSION BEGIN 00000080 4658914585
Jan 24 12:34:04.95: [  341]: <-- [4:ATA\r]
Jan 24 12:34:13.65: [  341]: --> [5:+FCON]
Jan 24 12:34:13.75: [  341]: ANSWER: FAX CONNECTION
Jan 24 12:34:13.75: [  341]: RECV FAX: begin
Jan 24 12:34:15.34: [  341]: --> [29:+FTSI: "       +46 570 10070"]
Jan 24 12:34:15.34: [  341]: REMOTE TSI "+46 570 10070"
Jan 24 12:34:15.64: [  341]: --> [22:+FDCS: 0,3,0,2,1,0,0,0]
Jan 24 12:34:15.64: [  341]: REMOTE wants 9600 bit/s
Jan 24 12:34:15.64: [  341]: REMOTE wants page width 1728 pixels in 215 mm
Jan 24 12:34:15.64: [  341]: REMOTE wants unlimited page length 
Jan 24 12:34:15.64: [  341]: REMOTE wants 3.85 line/mm
Jan 24 12:34:15.64: [  341]: REMOTE wants 2-D MR
Jan 24 12:34:15.75: [  341]: --> [2:OK]
Jan 24 12:34:15.75: [  341]: <-- [7:AT+FDR\r]
Jan 24 12:34:17.56: [  341]: --> [5:+FCFR]
Jan 24 12:34:20.13: [  341]: --> [22:+FDCS: 0,3,0,2,1,0,0,0]
Jan 24 12:34:20.13: [  341]: REMOTE wants 9600 bit/s
Jan 24 12:34:20.13: [  341]: REMOTE wants page width 1728 pixels in 215 mm
Jan 24 12:34:20.13: [  341]: REMOTE wants unlimited page length 
Jan 24 12:34:20.13: [  341]: REMOTE wants 3.85 line/mm
Jan 24 12:34:20.13: [  341]: REMOTE wants 2-D MR
Jan 24 12:34:20.13: [  341]: --> [7:CONNECT]
Jan 24 12:34:20.13: [  341]: RECV: begin page
Jan 24 12:34:20.13: [  341]: RECV: send trigger 022
Jan 24 12:34:20.13: [  341]: <-- data [1]
Jan 24 12:34:40.88: [  341]: RECV: 1146 total lines, 0 bad lines, 0 consecutive 
bad lines
Jan 24 12:34:40.93: [  341]: --> [17:+FPTS: 2,2219,0,0]
Jan 24 12:34:42.19: [  341]: --> [7:+FET: 2]
Jan 24 12:34:42.19: [  341]: RECV recv EOP (no more pages or documents)
Jan 24 12:34:42.30: [  341]: --> [2:OK]
Jan 24 12:34:42.30: [  341]: RECV send MCF (message confirmation)
Jan 24 12:34:42.30: [  341]: RECV FAX (00000080): from +46 570 10070, page 1 in 
0:27, INF, 3.85 line/mm, 2-D MR
Jan 24 12:34:42.31: [  341]: RECV FAX (00000080): recvq/fax00036.tif from +46 57
0 10070, route to <unspecified>, 1 pages in 0:2
9
Jan 24 12:34:42.31: [  341]: <-- [7:AT+FDR\r]
Jan 24 12:34:46.21: [  341]: --> [29:+FTSI: "       +46 570 10070"]
Jan 24 12:34:46.21: [  341]: RECV FAX: bin/faxrcvd "recvq/fax00036.tif" "modem" 
"00000080" ""
Jan 24 12:34:54.88: [  341]: RECV FAX: end
Jan 24 12:34:54.88: [  341]: SESSION END



# $Id: rc288dpi,v 1.4 1996/06/24 02:58:38 sam Rel $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Configuration for a Rockwell RC288DPi-based Class 2 modem
# (should also work for 144DPi-based modems).
#    Microcom DeskPorte 28.8S   firmware rev V1.100K-V34_DS
#    (and others)
#
# NB: DCD is toggled at page end during transmits; this can
#     cause problems on systems where it's not possible to
#     set CLOCAL and also enable RTS/CTS flow control.
#
#
CountryCode:            46
AreaCode:               589
FAXNumber:              "+46 589 14585"
LongDistancePrefix:     0
InternationalPrefix:    007
DialStringRules:        etc/dialrules.tele2
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0644
LogFileMode:            0644
DeviceMode:             0666
RingsBeforeAnswer:      3
SpeakerVolume:          medium
GettyArgs:              "-h %l F%s"
LocalIdentifier:        "+46 589 14585"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%y-%m-%d %H.%M.%S|Page %%p of %%t"
MaxRecvPages:           25
UUCPLockDir:            "/var/lock"     #This is as PPP does it, not kermit
UUCPLockMode:           0644            # /
UUCPLockType:           ascii           #/
QualifyTSI:             "etc/tsi"       #SP 97-01-26
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2          # use class 1 interface
ModemRate:              38400           # locked for fax sending&receiving
ModemFlowControl:       rtscts          # default
#
ModemNoFlowCmd:         AT&K0           # disable flow control cmd
ModemSoftFlowCmd:       AT&K4           # software flow control cmd
ModemHardFlowCmd:       AT&K3           # hardware flow control cmd
ModemSetupDTRCmd:       AT&D3           # DTR off causes modem to reset
ModemSetupDCDCmd:       AT&C1           # DCD follows carrier
ModemSetupAACmd:        AT+FAA=1        # enable adaptive-answer in Class 2
#
ModemRecvFillOrder:     MSB2LSB         # bit order of received facsimile
ModemSendFillOrder:     LSB2MSB         # bit order modem expects for transmit
#
ModemDialCmd:           ATDT%s          # T for tone dialing
#ModemResetCmds:        AT&F2..         # To be tested
#
# Chip locks the line rate and switches to xon/xoff flow
# control when receiving facsimile--we must follow suit.
#
ModemAnswerFaxBeginCmd: "<19200><xon>"  # lock line rate & switch flow control
#
Class2RecvDataTrigger:  "\022"          # character sent to modem to start recv


- -- 
Stefan Pettersson                  Voice +46-70-5933800   Kanard AB
spp@lysator.liu.se                 Fax +46-589-14585      Vretberga
finger spp@lysator.liu.se for my public key               S-732 96  ARBOGA
    "Who is General Failure, and why is he reading my hard disk?"
-----BEGIN PGP SIGNATURE-----
Version: 2.6.2i

iQCVAgUBMu5xfb3P24S/WuDFAQHrTwQAwGFxBsv1m3od4pQwIyqLx3vV+jBO1pGp
6qpwpQOU4Pt5lYd4bh1ziphVtDHOSgGRjvyWa7qkM2WeKmlMpgBFPQhcShXQGkRZ
qAfqp5Ar56c5TCPDLUAcNK5dpG4evbkCc31+YW0d5QttATpMf83PpPSzVseo/MUO
HGclih7rK0g=
=ZsNo
-----END PGP SIGNATURE-----