HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

Problem receiving fax



-----BEGIN PGP SIGNED MESSAGE-----


Hi all,
I recently installed hylafax 4.0 on my linux 2.0.0 box, and
managed to send out some facsimile. But I cannot receive any fax.
The machine accepts the connection, but then fails to receive
image data.

Modem Receive Fax Log

An attempt to receive facsimile on modem failed because:

    Missing EOL after 5 seconds (section 3.2/T.4)

    ---- Transcript of session follows ----

Jan 02 20:52:15.68: [  132]: SESSION BEGIN 00000010 49415282110
Jan 02 20:52:15.68: [  132]: <-- [4:ATA\r]
Jan 02 20:52:22.12: [  132]: --> [5:+FCON]
Jan 02 20:52:22.12: [  132]: ANSWER: FAX CONNECTION
Jan 02 20:52:22.12: [  132]: MODEM input buffering enabled
Jan 02 20:52:22.14: [  132]: RECV FAX: begin
Jan 02 20:52:24.18: [  132]: --> [28:+FTSI:"     +49 4152 872020"]
Jan 02 20:52:24.29: [  132]: REMOTE TSI "+49 4152 872020"
Jan 02 20:52:24.29: [  132]: --> [21:+FDCS:0,3,0,2,0,0,0,0]
Jan 02 20:52:24.29: [  132]: REMOTE wants 9600 bit/s
Jan 02 20:52:24.29: [  132]: REMOTE wants page width 1728 pixels in 215 mm
Jan 02 20:52:24.29: [  132]: REMOTE wants unlimited page length 
Jan 02 20:52:24.29: [  132]: REMOTE wants 3.85 line/mm
Jan 02 20:52:24.29: [  132]: REMOTE wants 1-D MR
Jan 02 20:52:24.48: [  132]: --> [2:OK]
Jan 02 20:52:24.49: [  132]: ACCEPT TSI "+49 4152 872020"
Jan 02 20:52:24.49: [  132]: <-- [7:AT+FDR\r]
Jan 02 20:52:27.06: [  132]: --> [5:+FCFR]
Jan 02 20:52:27.06: [  132]: --> [21:+FDCS:0,3,0,2,0,0,0,0]
Jan 02 20:52:27.06: [  132]: REMOTE wants 9600 bit/s
Jan 02 20:52:27.06: [  132]: REMOTE wants page width 1728 pixels in 215 mm
Jan 02 20:52:27.06: [  132]: REMOTE wants unlimited page length 
Jan 02 20:52:27.06: [  132]: REMOTE wants 3.85 line/mm
Jan 02 20:52:27.06: [  132]: REMOTE wants 1-D MR
Jan 02 20:52:27.83: [  132]: --> [7:CONNECT]
Jan 02 20:52:27.83: [  132]: RECV: begin page
Jan 02 20:52:27.85: [  132]: MODEM set XON/XOFF/FLUSH: input ignored, output generated
Jan 02 20:52:27.85: [  132]: RECV: send trigger 021
Jan 02 20:53:58.51: [  132]: MODEM TIMEOUT: reading from modem
Jan 02 20:53:58.51: [  132]: RECV: Missing EOL after 5 seconds
Jan 02 20:53:58.51: [  132]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled
Jan 02 20:53:58.51: [  132]: REMOTE HANGUP: Missing EOL after 5 seconds (section 3.2/T.4) (code 91)
Jan 02 20:53:58.55: [  132]: RECV FAX (00000010): recvq/fax00007.tif from +49 4152 872020, route to <unspecified>, 0 pages in 1:36
Jan 02 20:53:58.60: [  132]: RECV FAX: Missing EOL after 5 seconds (section 3.2/T.4)
Jan 02 20:53:58.60: [  132]: <-- [6:AT+FK\r]
Jan 02 20:53:58.82: [  132]: --> [7:+FHNG:2]
Jan 02 20:53:58.82: [  132]: REMOTE HANGUP: Call aborted,  from +FK or <CAN> (code 2)
Jan 02 20:53:58.82: [  132]: --> [2:OK]
Jan 02 20:53:58.82: [  132]: RECV FAX (00000010): session with +49 4152 872020 terminated abnormally: Missing EOL after 5 seconds (section 3.2/T.4)
Jan 02 20:53:58.82: [  132]: RECV FAX: bin/faxrcvd "recvq/fax00007.tif" "modem" "00000010" "Missing EOL after 5 seconds (section 3.2/T.4)"


I cannot find that EOL error mentioned in either FAQ or manuals,
and cannot even figure out where the error belongs to.
- From where is that ominous EOL expected: from the sending fax or
from my modem ?  
And does anyone know how to get around that ?

Tschüß,
						Dieter 
 
  _____________________________*______________________________
 /                          *       dieter.meinert@gkss.de    \
 \ Dieter Meinert    (-      **     http://w3.gkss.de/~dieter/ \
  \__________________A______*__*_______________________________/

-----BEGIN PGP SIGNATURE-----
Version: 2.6

iQCVAgUBMtD8gPYksnFoaQ6JAQENzQQA0pSLtks61WZH8C8uS+mjh/INCK6owLTd
8jEV5KlUyxRFozQOtkjNiTuRFvNDlgUoApU/wBuRW3zcHRg41a7kpk4ly6ttfmja
UpaD9ArcazW8b+VXYPDzTPC41qkATvGxsPKw+sZ5Er+hUQrEvf568/mHxbwwhLe1
RSE249ffFH4=
=7zYU
-----END PGP SIGNATURE-----




Project hosted by iFAX Solutions